A pair of Poulan 6 cubers

[leeha]

This saw iv'e had for a few years but needed a crank.
So i finally got to it and installed a good used crank,
all new bearings, seals, gaskets and a piston kit. I also
had a few NOS mufflers so i did a nice muffler mod.
Installed this nice brand new Poulan 32 inch bar with
404 chisel skip chain.

Lee

 

[Wildman1024]

Nice looking 6000 Lee. Glad to see you got it off the shelf and put back together. Just a note on the bar...Windsor says they are a 33" bar and 100Dl of 404 incase you didn't know the specifics. I run a 8 pin on my 6000 and you need 101 to make it work.

I forgot to mention I like your Muffler Mods. maybe i can get you to do that on my 6000 instead of it having 300 ports all over it.

 

[RiverRat2]

Wow it sure has an old Sachs Dolmar look to it!!!

 

[leeha]

This is the other S6000 that i bought a couple years ago
on ebay. It was listed part by part and i bought it all. It
was missing the carb manifold and air filter mount.
" Thanks Belgian for hooking me up with these 2 parts"
This saw is actually a Sacks Dolmar 152, The other is a 153
but both are at 100cc's. This saw also got a new muffler and
a muffler mod but i used a little smaller tubing on this one.
Got a new Sachs Dolmar 28 inch bar with 404 chisel chain.
Both saws are great runners now.

Lee

 

[RiverRat2]

Awesome!!! a very nice pair of old SD Poulans
:msp_wink:

 

[stihl_collector]

Hi Lee which is the same as the dolmar 153 mate? I need a muffler for one that is all. By the way very nice looking saws you have there.

 

[jrjuday]

I didn't know Deutz made chainsaws!

 

[leeha]

Hi Lee which is the same as the dolmar 153 mate? I need a muffler for one that is all. By the way very nice looking saws you have there.

The first set of pic's is the 153,
But they both have the same muffler.


Lee

 

[jrjuday]

Nice job on the big dogs.

 

[Duke Thieroff]

6 cubes is the hot thing right now.



I would love to get on that bandwagon, if I do say so myself.



Nice saws Lee.


Chris

 

[sachsmo]

Lee,


Have you ever seen a 152/6000 with the footpad,/mag handle bottom?

I have an old 152 that has it, could be the tank/handle was changed?

The serial# on the block is 152.

 

[RandyMac]

6 cubes is the hot thing right now.



I would love to get on that bandwagon, if I do say so myself.



Nice saws Lee.


Chris

Six cube saws have always been hot.

Gotta love the mean green Lee buddy.

 

[blsnelling]

Nice set of Poulans there Lee

 

[leeha]

Lee,


Have you ever seen a 152/6000 with the footpad,/mag handle bottom?

I have an old 152 that has it, could be the tank/handle was changed?

The serial# on the block is 152.

The second set of pic's is a 152 with the newer
style handle, tank assembly. I have seen a few
like this. I have a 152 that the rear handle wraps
around to the bottom of the tank. It is also held
on with pins.


Lee

 

[Modifiedmark]

Nice pair Lee, I'm working on getting a 6 cube Poulan myself but in yellow.

I ran Cbfarmall's 6000 and there tuff for sure.

The saw in my sig is a almost 6 cube Poulan!