Mono Line what model is it?

[pwoller]

Found a Mono Line on clist and was suprised when it started on the 2nd pull, suprised that it cut relitively well and suprised when it restarted on the 1st pull hot. I have some numbers that I located and was curous if anyone knew which model it is. Inside the bar mount it has the number 60, and on the outside of it is the letter R. there is a tag on the bottom of the saw that has these numbers on them 1418 line down 4246961. It has a 16 inch bar and an oregon chain too.

 

[pwoller]

Can somone give me direction on where to look for the model number?

 

[pinemartin]

Model: 47

MANUFACTURED BY:
MONO MANUFACTURING CO.
SPRINGFIELD, MISSOURI, U.S.A.
SERIES OR ASSEMBLY NUMBER:

YEAR INTRODUCED:
1966
YEAR DISCONTINUED:

ENGINE DISPLACEMENT:
4.7 cu. in. (77 cc)
NUMBER OF CYLINDERS:
1
CYLINDER BORE:
2.0 in. (50.8 mm)
PISTON STROKE:
1.5 in. (38 mm)
CYLINDER TYPE:
Aluminum with cast iron sleeve
INTAKE METHOD:
Reed valves
MANUFACTURER ADVERTISED H.P.:
4
WEIGHT :
18 lbs. powerhead only
OPERATOR CONFIGURATION:
One Man operation
HANDLEBAR SYSTEM:
Rigid
CHAIN BRAKE:
none
CLUTCH:
Fairbanks Morse centrifugal
DRIVE TYPE:
Direct
CONSTRUCTION:
Sand cast magnesium
MAGNETO TYPE:
Wico
CARBURETOR:
Tillotson HL series
MAJOR REPAIR KIT:

MINOR REPAIR KIT:

AIR FILTER SYSTEM:
Skinner ribbon element
STARTER TYPE:
Tecumseh automatic rewind
OIL PUMP:
Manual
OPERATING RPM:
4,500
IGNITION TIMING:
0.175 in. (4.44 mm) before TDC
BREAKER POINT SETTING:
0.020 in. (0.51 mm)
FLYWHEEL/COIL AIR GAP:
fixed
SPARK PLUG TYPE:
Champion J8J, Autolite A7X, AC M45
SPARK PLUG GAP:
0.030 in. (0.76 mm)
CRANKSHAFT MAIN BEARINGS:
Ball
FUEL TANK CAPACITY:

FUEL OIL RATIO:
1/2 pint to 1 gallon = 16:1
RECOMMENDED FUEL OCTANE:
Regular
MIX OIL SPECIFICATION:
SAE 30 non-detergent
CHAIN PITCH:
.404 in.
CHAIN TYPE:
Oregon
BAR MOUNT PATTERN:

SHORTEST GUIDE BAR SUPPLIED:
16 in. (40 cm)
LONGEST GUIDE BAR SUPPLIED:
20 in. (51 cm)
COLOUR SCHEME:

PAINT CODES:

ILLUSTRATED PARTS LIST:

SERVICE MANUAL:

COMMENTS:
used Power Products AH-47 engine type 1418A

 

[pwoller]

Model: 47

MANUFACTURED BY:
MONO MANUFACTURING CO.
SPRINGFIELD, MISSOURI, U.S.A.
SERIES OR ASSEMBLY NUMBER:

YEAR INTRODUCED:
1966
YEAR DISCONTINUED:

ENGINE DISPLACEMENT:
4.7 cu. in. (77 cc)
NUMBER OF CYLINDERS:
1
CYLINDER BORE:
2.0 in. (50.8 mm)
PISTON STROKE:
1.5 in. (38 mm)
CYLINDER TYPE:
Aluminum with cast iron sleeve
INTAKE METHOD:
Reed valves
MANUFACTURER ADVERTISED H.P.:
4
WEIGHT :
18 lbs. powerhead only
OPERATOR CONFIGURATION:
One Man operation
HANDLEBAR SYSTEM:
Rigid
CHAIN BRAKE:
none
CLUTCH:
Fairbanks Morse centrifugal
DRIVE TYPE:
Direct
CONSTRUCTION:
Sand cast magnesium
MAGNETO TYPE:
Wico
CARBURETOR:
Tillotson HL series
MAJOR REPAIR KIT:

MINOR REPAIR KIT:

AIR FILTER SYSTEM:
Skinner ribbon element
STARTER TYPE:
Tecumseh automatic rewind
OIL PUMP:
Manual
OPERATING RPM:
4,500
IGNITION TIMING:
0.175 in. (4.44 mm) before TDC
BREAKER POINT SETTING:
0.020 in. (0.51 mm)
FLYWHEEL/COIL AIR GAP:
fixed
SPARK PLUG TYPE:
Champion J8J, Autolite A7X, AC M45
SPARK PLUG GAP:
0.030 in. (0.76 mm)
CRANKSHAFT MAIN BEARINGS:
Ball
FUEL TANK CAPACITY:

FUEL OIL RATIO:
1/2 pint to 1 gallon = 16:1
RECOMMENDED FUEL OCTANE:
Regular
MIX OIL SPECIFICATION:
SAE 30 non-detergent
CHAIN PITCH:
.404 in.
CHAIN TYPE:
Oregon
BAR MOUNT PATTERN:

SHORTEST GUIDE BAR SUPPLIED:
16 in. (40 cm)
LONGEST GUIDE BAR SUPPLIED:
20 in. (51 cm)
COLOUR SCHEME:

PAINT CODES:

ILLUSTRATED PARTS LIST:

SERVICE MANUAL:

COMMENTS:
used Power Products AH-47 engine type 1418A

So what leads you to believe that? Just curious.

 

[pinemartin]

Of all the mono saws with the AH-47 engine this is the only model with the 1418 numbers that matched what you had originally posted

 

[pwoller]

Of all the mono saws with the AH-47 engine this is the only model with the 1418 numbers that matched what you had originally posted

ok thanks for the insite.

 

[056kid]

Good find!

She's got some funny dogs though, i wonder why they didnt take em all the way up?

 

[Mr. Bow Saw]

Nice saw. Model 47 is right...

 

[pwoller]

Looks like someone tryed to repaint it. Who knows what they did with the dogs.

 

[Cantdog]

Good Info

Well, I had to change my sig. Been thinking that I had a Mono 33 all this time when I actually have a 47 same as you!!! Still hard to believe that they still made saws that looked like that in 1966!! By then all your Macs and Homeys and even Lombards looked fairly modern but not the Mono!! Congrats on your score.

 

[Hunt4deer01]

Model: 47

MANUFACTURED BY:
MONO MANUFACTURING CO.
SPRINGFIELD, MISSOURI, U.S.A.
SERIES OR ASSEMBLY NUMBER:

YEAR INTRODUCED:
1966
YEAR DISCONTINUED:

ENGINE DISPLACEMENT:
4.7 cu. in. (77 cc)
NUMBER OF CYLINDERS:
1
CYLINDER BORE:
2.0 in. (50.8 mm)
PISTON STROKE:
1.5 in. (38 mm)
CYLINDER TYPE:
Aluminum with cast iron sleeve
INTAKE METHOD:
Reed valves
MANUFACTURER ADVERTISED H.P.:
4
WEIGHT :
18 lbs. powerhead only
OPERATOR CONFIGURATION:
One Man operation
HANDLEBAR SYSTEM:
Rigid
CHAIN BRAKE:
none
CLUTCH:
Fairbanks Morse centrifugal
DRIVE TYPE:
Direct
CONSTRUCTION:
Sand cast magnesium
MAGNETO TYPE:
Wico
CARBURETOR:
Tillotson HL series
MAJOR REPAIR KIT:

MINOR REPAIR KIT:

AIR FILTER SYSTEM:
Skinner ribbon element
STARTER TYPE:
Tecumseh automatic rewind
OIL PUMP:
Manual
OPERATING RPM:
4,500
IGNITION TIMING:
0.175 in. (4.44 mm) before TDC
BREAKER POINT SETTING:
0.020 in. (0.51 mm)
FLYWHEEL/COIL AIR GAP:
fixed
SPARK PLUG TYPE:
Champion J8J, Autolite A7X, AC M45
SPARK PLUG GAP:
0.030 in. (0.76 mm)
CRANKSHAFT MAIN BEARINGS:
Ball
FUEL TANK CAPACITY:

FUEL OIL RATIO:
1/2 pint to 1 gallon = 16:1
RECOMMENDED FUEL OCTANE:
Regular
MIX OIL SPECIFICATION:
SAE 30 non-detergent
CHAIN PITCH:
.404 in.
CHAIN TYPE:
Oregon
BAR MOUNT PATTERN:

SHORTEST GUIDE BAR SUPPLIED:
16 in. (40 cm)
LONGEST GUIDE BAR SUPPLIED:
20 in. (51 cm)
COLOUR SCHEME:

PAINT CODES:

ILLUSTRATED PARTS LIST:

SERVICE MANUAL:

COMMENTS:
used Power Products AH-47 engine type 1418A

 

[Hunt4deer01]

If you dont mind me asking where did you find this information? I have a mono 1086 on the frame and the tag has 1533B 6023336 that I'm trying to find specs for

 

[ML12]

Chainsaw Collectors Corner. Here is a link:
http://www.acresinternet.com/cscc.nsf/

There are specs listed for almost every saw made. Its a good place to start, but some of the specs aren't always accurate.