Sold Duce Built 372XT

[chipper1]

Great running saw that runs like the fresh build it is.
I've ran a few tanks thru this one and she pulls great, sure to get stronger as it gets broke in.
It has a 390/wide clutch cover and does a great job moving chips. If I'm not mistaken the chassis is a 2018 and it had new bearings installed when built.
It has an unlimited coil and is very easy to tune.
The muffler has some small cracks around the tubes where the bolts go, but it's very solid. The muffler has also been opened up under the deflector.
I'll see if I can find the original thread, @Duce remember this one?
$425 plus shipping net to me for the powerhead, PayPal preferred.
Here'a a video of it running in seasoned ash(very hard) with a 24", it will pull just like this on a 24" green red oak log as an example of how hard it is.

 

[chipper1]

Pics for your viewing pleasure.
There's also pictures of the muffler in this link.
https://photos.app.goo.gl/ppDB7hEL5zT1dt4D9

 

[Deleted member 117362]

Yes I do. OEM p/c take off only test run. SKF bearings, new lines filter, nice OEM clutch, gaskets and seals. Should run a long time with proper care. GLWS.

 

[chipper1]

Yes I do. OEM p/c take off only test run. SKF bearings, new lines filter, nice OEM clutch, gaskets and seals. Should run a long time with proper care. GLWS.

Thanks, maybe that was one of the cylinders you got from me?
I have another here if you need it, and a line on another too, as well a couple 346 nib and a 390 sitting her just in case .

 

[fulladirt]

Nice saw, I got a Duce Built(tm?) 372XT a couple months ago, now it's one of my favorites. My buddy never ran a 372 gave it a rip and was like holy %#%&!
GLWS Brett

 

[wlc7511]

I have a Husky 345 id trade along with some cash.

 

[chipper1]

I have a Husky 345 id trade along with some cash.

Thanks for the offer my friend, mainly looking to sell outright on this one.

 

[chipper1]

Nice saw, I got a Duce Built(tm?) 372XT a couple months ago, now it's one of my favorites. My buddy never ran a 372 gave it a rip and was like holy %#%&!
GLWS Brett

He does a great job on any saw, and the 372's are great to start with.
Thanks for the comments.

 

[muad]

Oh, I like that!!


I wonder how much trouble this would get me in with the Mrs...

 

[9050LX]

Are the SKF crank bearings all metal?

 

[Deleted member 117362]

Yes, from Italy.

 

[Deleted member 117362]

Are the SKF crank bearings all metal?

Yes.

 

[Oregonsaw]

If this is still here when my taxes come back..

 

[chipper1]

If this is still here when my taxes come back..

Sounds good. Just got ours done last evening .

 

[9050LX]

What about the chain saw relief act? Should be coming soon.

 

[chipper1]

What about the chain saw relief act? Should be coming soon.

It's currently happening right now, I'm trying to relieve some of the saws I have lol.
I'm heading out now to do some cutting, getting firewood for 21/22 in the woodshed from the woods, might as well since the weather is good right now and the mosquitoes aren't biting, that wont last long.

 

[Oregonsaw]

What about the chain saw relief act? Should be coming soon.

They can’t get it out of the Senate because it’s stuffed full of pork.

 

[Deleted member 117362]

You want me to do a buy back? Oregonsaw, the pork has been released.

 

[chipper1]

You want me to do a buy back? Oregonsaw, the pork has been released.

Lol.
Wouldn't I have to do that to qualify as a "buyback".

 

[Deleted member 117362]

Are the SKF crank bearings all metal?

Do you want non-metal retainers. I can do those also?