036

I have a 036 non-pro (red control, no decompression button). The current air filter is wire mesh (1125 120 1600 the half closest to the carb and 1125 120 1605). That may be the "Arctic" version from what I have read here and other places. I'm not in the Arctic, so I assume I should be using one...

Hey everyone. I just bought this used 036-cylinder off eBay. It has some odd pitting, as seen from the pictures. The ad said no scoring but didn’t mention anything about the pitting. The pictures were too far away and out of focus to see the issues. My question is, would you run it, or would you...

I am in search of a smaller ported saw for a friend. 50cc class preferably Stihl but open to husky as well. Anything out there?

Alright guys I’m new here but already tell a lot of you have a saw addiction and I am quickly catching that bug. I heat my house And barn with a wood burner So I split and cut a ton year round. I want to get MY first saw, I’ve been using grandpas old mcculloch for years and am ready to by my...

Sorry if this is not the right place to post, not really mod but it’s for use with the fire department. I put a new OEM carb on a 036 pro and the low screw will not richen up and slow the saw down. It just increases the Rpms, yes I’m turning counter clockwise. I will vacuum/pressure test in the...

Any of you guys looked into putting an 038 magnum p/c on an 034. I was having a discussion about big bore options on my buddies 034 and wondering if it could be done. I don't mind some extra machining if it is a doable mod.

Looking for a cylinder for stihl 036

I figure one of you "AS" geniuses have to know this one. Because I'm stumped. I am trying to figure out if the ms361 shared any parts with the 036 or if I have some sort of Frankensaw situation going on. A few months back, I had finished rebuilding my trusty old ms361 that was the first new saw...

I've got an older 034 that I picked up in a "box of parts" state, prev owner pulled carb and whole air side off presumably because of carb issues. Carb was a Tillotson and missing almost all the parts, and I couldn't find a good source for complete replacement. Saw has good compression...

Hyway pistons, that I'm not going to be able to use. So I'd like to move them all out. $28 shipped EACH MS261 popup 036 Popup MS461 Popup Then I have these two. I can't even remember what they go to. One flat top, the other is a popup, and both 52mm

https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F372641627930 Selling my 036 pro saw. Runs n cuts great, I just prefer my huskie so its gotta go.

Looking for a good crankshaft for a Stihl 036 , ms360. Or a good crankcase with one already installed, or a parts saw if it has a good bottom end. Thanks.

Stihl 036 PRO builder complete minus crankcase and bearings. Comes with everything else needed to rebuild your 036PRO. Aftermarket parts are zama carb rebuild kit, meteor piston, caber rings, cross performance air filter. Jug is OEM MAHLE and will include original piston, but I had planned to...

I got this from Hyway because I was supposed to test their popup kit for the 036, but I was sent three of the regular kits by mistake. So I just figured I'd sell them to help out some others. Cylinder kit for an 036/MS360, or use it convert your 034 to 036 specs. Asking $60 shipped. I AM NOT...

Ok here it Goes. I have a Stihl 045 and 036 that both experienced piston and cylinder scoring on the exhaust port side. I used 93 octane (4gal) and (2) stihl 2 cycle mixes (orange ones). FS trimmer is fine 55 series blowers are fine and the ms210 as well. All have used the same fuel. I was...

Hello All. Newbie here. (I even Posted this in the milling forum... Reposted over here) Great info, I find myself coming to this site all the time. Figured I might as well sign up and join in. I have been given an old Stihl 034AV by my dad that needs some serious attention. GOOD: - Holds Gas...

Hello All. Newbie here. Great info, I find myself coming to this site all the time. Figured I might as well sign up and join in. I have been given an old Stihl 034AV by my dad that needs some serious attention. GOOD: - Holds Gas - Brake works - Bar's straight - Pull cord returns beautifully -...

Im looking for a Stihl saw in either a 026/260/261 and the like or a 036/360/361/362. Not picky on much, just looking for a clean saw at a good price. i would even go for a 044/440/441 if the price is right. Bar length is not a major detail to me either. Thank you!

Good evening, gentlemen! I'm currently trying to clean up a Nikasil plated cylinder from an 036. It had some aluminum transfer from the piston and some scoring. I tried please clean it up with sandpaper but the plating is very hard and it doesn't really do anything. So I went ahead and took some...

Good evening, gentlemen! So I had this chinese top end for a 036 that I popped in there for testing purposes. And here's the result after about 2 tanks, half of which was really adjusting and playing around with different settings. In the pictures you can see that the spot where the circlip is...