046

hey guys! looking to purchase a new saw and ive narrowed it down to down to either a 044/046 or a 066. wanted to get some opinions. planning on using it for some medium to large firewood bucking and felling with likely starting with a 28in bar (maybe upgrading to a 32in later). weights not a big...

As you can see there are 3 am. Ones got piston with. $20 each for two black ones and $10 for other one. $35 each for the others. Come on gents want these gone. Ill cover shipping

$30 shipped

My 046 is missing the metal guard that protects the fuel tank, is this something that I need to get replaced? There is already an extended rubber chip guard (black tab in photo) for the cover, so curious if this is enough protection for the tank. Thanks.

I've got a Stihl ms460 magnum in good used shape, 170 lbs on compression. Runs great and oils as it should. I bought this one in a lot of 6 running saws a few days ago. The only thing I've done to it is cleaned it up and inspected it well, it cranks on 3rd pull when cold and 1st when warm. Has...

Stihl 044 K&S P/C Long Block. Crank turns over smoothly. Slight bit of play on flywheel side bearing. No scoring visible on P/C. Case bottom is in mediocre condition and shows wear. See pictures $75 shipped in lower 48 except for Left Coast (PM for shipping quote). PM with any additional...

I just found a REALLY nice unicorn and I have decided to sell my MS460 Magnum. All OEM & very clean as I hope you can see from the pictures. PHO w/ dual spikes, roller chain catch, decomp plug, OEM HD filter and Stihl Pre-Filter band $635 includes shipping w/ insurance via FedEx Ground...

Any interest in a new ms462 with heat PHO somewhere around 1400USD shipped from Sweden? These just showed up here and I figured I would see if anyone is interested, I can get 2 of them at this price.

Looking for a Stihl 70cc size chainsaw and narrowed it down to these models. I already have a 372xp but want to try out a larger Stihl (have a 026pro). Saw should be all oem. Not looking for rebuild. Doesn’t have to be a show queen but not one beat to crap. Let me know what you have. Thanks, Joe

Looking for an oem cylinder for a ms460.

Dad's 046 magnum has the original air filter (and everything else) that has never been changed, but he does clean it. Lately he said it's been losing power as he cuts with it. Says it's fine when he starts and then bogs down progressively. He decided he wanted me to put a new carb and filters in...

Hello, I am working on a Stihl ms 460 and need a clutch side half. I may need some other parts for the saw as well, so let me know what you have. Thanks, John S.

hi guys, I'm wondering if anyone knows whether an 046 carb will fit an 044? And if there was a non compensating version of the 046 carb made? I'm building a ported fairly highly modded 044 and I'm worried about running lean, it'll be setup on the air filter side with a custom bell mouth and...

Picked up an old 046. I checked the compression and it was at 90lbs so I recently replac d the piston/rings, coil and rebuilt the carb. It started up with some starting fluid and idled but kept bogging and dying when I tried to throttle up a bit. After about 6-7 times it stopped running all...

Found a small amish shop near me that has many new in the box older stihl models wanting to buy a new saw any particularly good models to look out for

Hey guys, I bought a new 461R. The 3/4 wrap wasn't for me. Made about 10 cuts before I made the switch to the 1/2 wrap. So it's like new. Make me a decent reasonable offer plus shipping.

Hey all, I'm in the market for a Stihl 044 or ms440. Dead or alive, it doesn't matter. A "parts saw" would be perfect. I don't really care what condition the saw is in. All I really need is a saw with a good case and a good 12mm crank. I'm hoping to find something in the southern Ontario...

Just picked up a Stihl 046 Mag, no history on the saw. (It was Pawned) It's in good shape, a little used, but not terrible, and for the price, it was in MUCH better shape than the others I had the opportunity to buy. So....what should I do before I run it? I already have a new 20" bar/chain...