084

$125 shipped each One is a 3/4 wrap with a good weld (in pic) and new Stihl hose. the other is a factory full wrap with two layers of heavy heat shrink.

Slight Knick in corner shown in the picture, otherwise brand new mint condition. $300 shipped

Crankcase- factory replacement case no serial number. All threads are good except the one wonky top cover hole but it holds a bolt. No breaks, weird paint on flywheel half. Sold Crankshaft- used good condition -Sold Clutch cover- good shape no stripped holes sold Flywheel- single key good...

All the usual suspects, take-offs, broken or that your done with now. Any 1124 or any large saw parts for Stihl will be considered. 075/760, 105s, 050, 051, TS510, 070, 090, ect... If you have an add here listed I've seen it already. Plastics Starters and parts Clutch covers Oil pumps working or...

660 650 066 064 front muffler covers. No outlet type. Busted and spun 660/066 cases or halves with or without cranks. Busted or not tank handles for 1122 or 1128 034, 036, 034S 360 360P parts and builders boxes. 034 plastics 084 anything or 1124 saws and parts. Ms400's or burnt jugs and pistons...

Hi there! listing my Stihl 084 for sale. the saw runs and cuts excellently. This 122cc torque-monster has great compression and overall is in very nice condition. the saw comes with a Maxflow air filter, Pro-safety full wrap handle, and 36 inch Stihl ES bar. also included in the sale are two...

Looking for a bar for my 084. Figured I'd ask here before I bit the bullet and bought new. Willing to pay the right price for a nice used bar Thanks, Hank

I recently picked up an 084 and have some 40-50" wide trees to get to. I've been trying to figure out the best bar setup. I'm set on Cannon because from what I have read from you fine folks, they are the most rigid long bars. So I'm either going with the 60" SuperBar or the 56" double ended bar...

Looking for large mount bar 42" 3/8 .063. So far I've bought 4 bars on eBay the people claimed were large mount that fit Stihl 070/076/084/088/ 090/ and MS880. Everyone of them has been the small slot for the smaller saws. Getting VERY frustrated. My 36" bar is too small milling and need a...

I finally found some ethanol free gas. The 044 I finished runs fabulous on it. Better than any saw I've built. I need to try it on the others now. Working on the 084. I wasn't going to put bearings in it but decided to anyway. Magnified examination found wearing spots in both crank bearings...

Hi all, My search for the illusive slotted nut for the HD air filter, part number 1124 141 8305, has so far been unsuccesful. I was wondering if this part can be replaced by a similar slotted nut, like the one with part number 1124 141 8300 or 1125 141 8300. I know STIHL is very good in reusing...

I have a panel style filter setup now and want to convert to HD. Need a base and cover if anyone has one for sale??

Hi Guys. Does anyone have any old 084s laying around. I'm chasing a new fuel tank and handle. Currently have one with the handle bolt holes stripped. Any help appreciated. Cheers Alex.

Looking for a big old saw, 110cc+ Will consider running or a simple project What do you have?

Bar is nearly brand new - the miniscule wear-marks are from running it on a saw for a tune only. Never touched wood. Chain is RMF (Rapid Micro semi-chisel full skip), not new - About 8mm on the teeth. $140 shipped.

Hi there. I'm looking for a runner or project saw (3120, 880, 088, 084) I can turn into a hot saw for timber sports. My budget is anywhere from 0 to 400 bucks for the right saw. Hopefully closer to zero... :) Thanks. And if anyone had any advice for how to go about this I'm all ears

dear milling friends, I have started a new project lately, I've bought a beech logs that measures 1.85 meter/ 73'' at the butt and is 5 meters long (196'') It weights 9.5 tons. I have been chainsaw milling since i was 18, so a couple of years of experience but this is my largest log so far. but...