088

Let me know what you’re interested in or for more pics/ details. All parts are new except the brake flag and cylinder. Carb has a 1.02 jet I put in it. Also have a crank case and other odds and ends.

Hi all, I'm trying to diagnose this whirring/screeching sound at idle on my Stihl 088. It happens when the chain brake is both engaged and disengaged. I think it goes away as the RPMs increase, but it's hard to hear over the engine noise. The easiest way to replicate the noise is by pulling...

Only about an hour of run time since I went through it. Has been modified, can swap it out for a stock cylinder. 195psi compression, new pro safety dogs, new clutch cover and new poly flywheel. Has a 461 coil with 880 leg to bring the rev limiter up. $1600 + shipping

Hey guys just wondering if anyone has swapped a 404 chain to a 3/8 sprocket on an 088/ 880? It is as simple as just changing the sprocket? Cheers

All the usual suspects, take-offs, broken or that your done with now. Any 1124 or any large saw parts for Stihl will be considered. 075/760, 105s, 050, 051, TS510, 070, 090, ect... If you have an add here listed I've seen it already. Plastics Starters and parts Clutch covers Oil pumps working or...

I have for sale a good used 088 cylinder, it looks to been cleaned up in the past, cylinder walls are very smooth, all threads are good, will come just as pictured, please feel free to ask questions and for more pictures, this cylinder uses the bolt on exhaust, asking 220 obo shipped anywhere in...

Brand new take off Stihl spikes with hardware and roller. $25 plus shipping.

Looking for new condition 088 parts. Need top buffer with bracket, impulse line and intake. Main concern is intake. Only need rubber.

Looking for large mount bar 42" 3/8 .063. So far I've bought 4 bars on eBay the people claimed were large mount that fit Stihl 070/076/084/088/ 090/ and MS880. Everyone of them has been the small slot for the smaller saws. Getting VERY frustrated. My 36" bar is too small milling and need a...

I was looking on the tradin' post this morning and noticed someone was selling a 25" and 30" .404 bar for the larger Stihl saws and there seemed to be some sparked interest and they seemed to have sold. I was wondering what a guy thinks he could get for a used Stihl bar and what ones are worth...

I finally found some ethanol free gas. The 044 I finished runs fabulous on it. Better than any saw I've built. I need to try it on the others now. Working on the 084. I wasn't going to put bearings in it but decided to anyway. Magnified examination found wearing spots in both crank bearings...

I'm new to this site other than coming here to read old posts when I need info that I can't find elsewhere. So I'm not sure if this post is going to be in the right place on the site but here goes nothing. I have a Stihl 090 that I purchased and was going to use it for milling but before I had...

HUSKY 3120 XP W/ 48" .404 CHAIN COMPLETE GROUND UP REBUILD!! Completley rebuilt from the ground up. All OEM parts only.! Crank case bearings and seals Complete gasket set Rebuilt carb and fuel line Near new OEM top end Many small parts , nuts and bolts Drive sprocket Pull rope and handle...

Hello wonderful and insightful members of Arboristsite! I have lurked around this site for a short while now and am only recently getting pretty serious about chainsaws. I have read a lot of great information on here from all of you and it has gotten me out of, or rather avoided, some...

Bar is nearly brand new - the miniscule wear-marks are from running it on a saw for a tune only. Never touched wood. Chain is RMF (Rapid Micro semi-chisel full skip), not new - About 8mm on the teeth. $140 shipped.

Hi there. I'm looking for a runner or project saw (3120, 880, 088, 084) I can turn into a hot saw for timber sports. My budget is anywhere from 0 to 400 bucks for the right saw. Hopefully closer to zero... :) Thanks. And if anyone had any advice for how to go about this I'm all ears