261

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. W

    Got burnt buying an 026

    I have been looking for another 026 for a while, found one on kijiji, ad stated “ runs just like it should”. Talked a bit with the fella and got him to ship it to me. Guy leaves the bar and chain on his bench and ships just the head. I check it all out, put some fresh gas in and it fires up...
  2. Chewbacca10

    Help me with my two-saw plan

    I’m looking for some thoughts about a two-saw plan. I heat partially but not exclusively with wood, and I help a couple of friends with maintenance on their property (260 acres of fields and hardwoods). My primary uses are bucking trunks and limbs as well as cutting trails. Right now, I have...
  3. T

    MS261 Clutch Cover

    Hey I have a ms261 (c/cm?) which I guess is considered gen 1. It’s mtronic but has the older style clutch cover with captive bar nuts not the newer style. Does anyone know if I can change the clutch cover out to the newer style? I know it’s not a direct replacement but does it work with other...
  4. L

    MS 261 - piston and rings after 60l/~15gal of alkylated gas + HP Ultra at 33:1

    Hello, I'm pretty new on here, used to be a lurker until recently. So I just got a new MS 261 (ver 3/carb) this spring and scrolling around during that time (including that 400-500 pages oil thread, oh god) I noticed that the veterans on this site aren't big fans of this oil. "Smells bad"...
  5. N

    New chain for Stihl 261 questions

    Long time reader, and student of the arborist site, and normally find my answers already posted, but I searched for this one and couldn't find a clue, so here goes. I have a 261 with the standard sprocket and a 20" green bar. standard 325 chain. I need to replace a couple chains that are a few...
  6. Overkill338

    Want to Sell Aftermarket Pistons

    Hyway pistons, that I'm not going to be able to use. So I'd like to move them all out. $28 shipped EACH MS261 popup 036 Popup MS461 Popup Then I have these two. I can't even remember what they go to. One flat top, the other is a popup, and both 52mm
  7. Levi of the North

    Sold New Stihl MS 261 (non-M-Tronic)

    Looking to buy a new Stihl MS 261 without M-Tronic. Probably a needle in a haystack here in Canada, but if anyone knows a dealer with one in stock (or is selling one new), please let me know! UPDATE: Found one in Canada!
  8. Overkill338

    My MS261C Build Thread

    Ok, it started at my $80 saw thread and now it's time to go back together. I ordered parts and cleaned it up a little bit. The case needs a little more "toothbrush" work, but hey, I think its alright. As far as parts, it's all new and oem. Piston kit, carb kit, fuel solenoid, handle...
  9. Overkill338

    Video of a 261C with a Hyway popup

    It's all stock except for the Hyway popup piston and base delete. Cutting oak.
  10. Overkill338

    Sold Hyway PopUp kit for 261

    I decided I wont be using this on my 261. Asking $50 shipped. Here is a video of my friends MS261C, all stock except for the Hyway popup piston and a base delete. Here is a video of my friends 261. All stock except for a Hyway popup piston
  11. X

    Want to Buy Stihl 20/260 variant or 036/360 varient

    Im looking for a Stihl saw in either a 026/260/261 and the like or a 036/360/361/362. Not picky on much, just looking for a clean saw at a good price. i would even go for a 044/440/441 if the price is right. Bar length is not a major detail to me either. Thank you!
  12. D

    Ms261cm is it best in its class?

    Might buy one
  13. wat648

    New member of my Stihl family

    So, after many hours of research and thought, I finally pulled the trigger on a new MS261cm! Immediately took it to the woods to break it in. I am very impressed! Light, fast, a joy to run. Highly recommend.
  14. Michaelmj11

    Want to Buy Stihl MS261 Canadian Type II

    Looking for Canadian Stihl dealer, or some other interested kind Samaritan who would be interested in helping me aquire a MS261 type II
  15. V

    Want to Buy Husqvarna 288xp and 262xp cylinders NEEDED

    I am in need of cylinders for a Husky 288xp (54mm) and a 262xp (48mm) Looking for Oem with or without decompression. It just needs to be in usable condition Thanks!
Back
Top