395xp

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. bradislav

    Can this be a fake?

  2. A

    395xp won't start after milling - has it overheated?

    Hello everyone! I'm a bit stumped. Hoping someone can help with opinions as to what might be wrong with my saw, a 395xp. Running a 3-ft bar with skip tooth milling chain. I was milling a long slab (23-ft),and towards the end, the saw leaned out, and ran out of fuel. OK, that happens with such...
  3. J

    Withdrawn Deleted

    Found the part thanks
  4. joeyslinger

    Holzfforma g395xp issues

    Hi everyone, looking for some advice. My brand new cs will only start under full throttle, can't even get nice sputtering with choke on. It will also run at full speed when the gas tank gets fully depleted. I tuned it up what I thought was nice but this didn't solve my issues. From looking it...
  5. A

    Contract Climbing Starting up help

    I am curious if there are any contract climbers on here that may have some wisdom they could spare as I am just starting out in the contract realm of tree care. Big questions would be reasonable day rates, and if anyone has had any luck with traveling for work.
  6. Paul Silvestri

    Want to Buy Big CC saw wanted

    Looking for a good 80cc or over saw, doesn't need to be running or beautiful either. I don't mind a project if the bottom end is good. Prefer husky and I don't care how old it is. Might be able to trade also depending on what it is. Thanks!
  7. Bag of Nails

    New sprocket causing issues?

    Got this new Gb titanium bar very heavy 44" for milling on my 395xp so I had to swap out my 3/8 sprocket for a 404 and now I can only pull the starter rope out when the chain break is off won't budge an inch with it on and even when it's off and I can get a good pull it's not really wanting to...
  8. Stonewoodiron

    Husky 395xp milling setup

    Hi all! about to pull the trigger on purchasing Husqvarna 395 XP with a 36 inch bar as well as the corresponding Granberg Alaskan mill. I’m currently milling with a 450 Rancher, Granberg mini mill, and homemade (ish) vertical canting mill. I don’t want to kill my rancher. I would like to keep...
  9. Ol' Brian

    What did you cut down today?

    I thought this might make an interesting thread... Big Oak tree taken down this morning. I was hoping to make a nice log out of it, but it looks like it's going to be firewood :nofunny:. 395xp 32" bar. 46" stump. This big dude shook the ground pretty good when it hit. It will probably lay...
  10. husqvarna93

    Want to Buy Husky 395

    Hi looking for a 395 or 394. Running or not. Thanks
  11. tntblaster14

    Sold Husqvarna 346 359 372 395

    I would REALLY prefer a local pickup as I have a lot of complete builder/parts saws, and a lot of loose parts (new cylinders, pistons too for these models). I live in 21042 Maryland, but can travel if someone is serious within reason. I have to move in the very near future, and will not need all...
  12. quattro90

    Sold Husqvarna 395xp

    FS a very good condition 2001 model Husqvarna 395xp PHO with mild port work and muffler mod. All OEM except muffler, Meteor piston, and Caber rings. OEM full wrap with West Coast kit and front case protector. $750 Shipped PayPal F&F to those in EST, CST, MST. If in PST or outside the continental...
  13. Jacob J.

    Want to Buy Husqvarna 395 flywheel, 20" large-mount Husqvarna bars

    Hey guys- I'm looking for a Husqvarna 395 flywheel and two 20" large-mount Husqvarna bars in .050" gauge x 3/8ths pitch. I got cash and trade. Thanks!
  14. beavis331

    Want to Buy 395xp Flywheel

    Looking for a flywheel for a project 395xp. Can anyone help a guy out?
  15. HopperGirl

    Want to Buy 395xp $500

    Want to buy a good condition/good running 395xp! Cash in hand right now! Will pay shipping if you're not close enough to pick up!
  16. Azntve76

    Want to Sell 395XP 850 plus shipping OBO

    I have a 395XP that has been sitting on a shelf in my garage for the last year. Bought it when I was still in Missouri and used it around the farm for 6 or 7 months. Has not seen heavy use, This saw was too heavy for constant use so it has maybe 50 or so Starts on it. Bought it the Gingrich Saw...
  17. nighthunter

    Sold Looking for a saw project

    looking for a 660/880 or 395/3120 project saw.im located in Ireland so shipping is a must , pm me any info Thanks
  18. huskyslinger

    Want to Sell 394xp Cyl, Piston, others

    As title says, looking to rid my shop of these extra parts. Pm with inquiries
  19. N

    Sold husqvarna 395xp $650

    Husqvarna 395xp, runs and cuts great, new oem muffler and brake band.needs nothing.$750 plus shipping.it will ship with no bar and chain to save money on shipping
  20. Jacob J.

    Want to Buy Husqvarna 394/395 full-wrap handle, Fundamentals of General Tree Work book

    Hi Everyone- I'm looking to buy two things- a decent full-wrap handle for a Husky 394/395, and a copy of Jerry Beranek's book- "The Fundamentals of General Tree Work". I used to have several copies but gave them all away as gifts. Thanks much, JJ.
Back
Top