550xp

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. L

    Loose/spun PTO side bearing on a 550 MKII

    Hello everyone, i'm rebuilding this 550mk2 Who suffered from PTO side bearing failure, kinda evergreen on a 5 series😬. It Is mu First bottom end rebuild, and It was going all smooth until i found out that the inner race of the new bearing spins almost freely on the crankshaft. Still, i had to...
  2. pining_fir_yew

    First Brake Band fail happened today...

    So, just how silly should I feel for not catching the wear on this earlier? Second, is this a fairly common point of failure in any one else's experience? I did measure the material width afterwards (.046" or 1.168 mm) which is thinner than the recommended minimum .. but jeez not a whole lot...
  3. L

    550xp used cylinder

    I'm looking for a used 550/545 mk1 cyilinder, the one that i have now may not be salvageable. Lots of transfer and scoring. Ideal would be a cheap OEM jug with some polishing to do to it also.
  4. T

    365 Special Project

    Picked up this 365 Special quite a while back that had a crank seal leak and just finally got to it last night. Excited to fire it up and get it in some wood soon! If it ever dies I do plan on throwing the 372 top end on it but until then what should i do with this thing? Already has a muffler...
  5. Blueline Hobby

    New to the forum!

    Hey guys and girls, my name is Mike and i am new to the forum. Been an avid outdoorsman my whole life and recently trying to get into the wood business instead of just doing it for myself. #bluelinewoodservice Anyway glad to be apart of this community! Here is a pic of some of the saws!
  6. L

    Want to Buy Husky 550xp CYLINDER KIT

    Hi guys, I'm New on the forum, I'm an italian boy who's beginning to appreciate the world of arborists. Here I am with a little big issue: some months ago I was gifted a Husky 550xp MY '13 (one of the first ones, know they had some carb issues and other stuff) that wouldn't start. The old owner...
  7. quattro90

    Sold MMWS Jonsered 2253

    FS Jonsered 2253 with the MMWS treatment. The saw has less than 1 hr of runtime according to the dealer who updated the carb software in Sping 2019.if you’re not aware of this model it’s identical to the 550xp MK1 but just in red. $750 Shipped Paypal F&F to your door if you live in EST, CST, or...
  8. Sukpad

    550xp testing out 3/8

    With all the hype about the new mk2 saws and new stuff coming out I decided it's time to take my 550xp and just have some fun with it. So I went and got a new sprocket and a new 18" bar and chain and here it is. Did a few test cuts and plunges on some cherry out in the back yard. I'm liking it...
  9. WoodsliverDan

    Husqvarna 550xp bearings

    Hi all, looking for information on the 550xp pto side bearing. I know there has been an update (or 2?) since the 550 and 562 has been released. I am looking at bearings and see both the 525 43 42-01 and the 525 43 42-03 bearings listed for the clutch side. Which one is the one I want? They are...
  10. quattro90

    Sold Husqvarna 545

    Husqvarna 545 fully rebuilt from the crank up with all NEW OEM parts. Cylinder, piston, ring, bearings, seals, case gaskets, lines, filters, clutch drum, oil worm gear, .325/7T sprocket, spark plug, etc. Pressure and vac tested 100% using OEM Husqvarna block-off plates. I have video of it...
  11. quattro90

    Sold Husqvarna 545/550xp Cylinder

    Husqvarna 545/550xp cylinder in excellent condition no transfer, scoring, or other damage. It still has the cross hatching in the cylinder from the factory. P/N 577 76 47-06 Also fits Jonsered CS2252/2253 $50 Shipped
  12. Shanman55

    Husqvarna 550 xp . Whats a better replacement bar than my stock 18 inch ?

    Hey folks i want to put a new bar on my 550 xp . 18" What do you guys recomend and i can get in Canada? Thanks .
  13. A

    50cc high rev Pro or 60cc higher torque for general Farm work

    Hello to all here and thanks for a very informative website. This has probably been done to death before but I have not found a satisfactory answer. TLDR: Should I keep a screaming 50cc high rpm pro saw for farm work, buy a 55/60cc slower rev higher torque workhorse or just stick with my 40cc...
  14. P

    Sold 545, 550XP, or similar in Atlanta area

    Looking to replace a vintage 55 that was accidentally destroyed. (Bushhog shredded) Trying to locate a new or used Husqvarna 545, but have not been able to find an Atlanta dealer in stock. Have found 550XP's, all at $599 Would also be interested in a used 550XP, or 346. Trying to stay in that...
  15. T

    First pro saw 550xp!

    Broke down and bought my first new pro saw, a 550xp. Going to be using this saw heavily for firewood but also some clearing on the property I just bought. I immediately had the drive switched over to 3/8" and Im running the Husqvarna 20" bar with a loop of Husqvarna H47 on it. I already want to...
  16. K

    Good compression on used 550xp?

    I'm looking at a used 550xp. The seller isn't completely sure of the history. But, by the looks of it, it's in good shape. Gray paint on the clutch guard isn't scuffed to pieces yet - good sign. Seller tested the compression at 145 cold. He's at 180 ft, for what it's worth. Here's the question...
  17. ChipChecker83

    Husky 550 xp dies mid cut?

    Hey guys new to the site but I've been stalking threads for years. That said I need help with a saw a bought from a member. It's a 2013 model 550xp. Only blows 110psi on compression gauge but starts and seems to cut well. For the first 10-15 minutes anyway. I was blocking firewood tonight...
Back
Top