I was doing my first oil change on my new to me 90xp chipper . Grabbed some 15w 40 semi synthetic oil at walmart and apparently it was not stocked with the same oil so 3 quarts of 10w30 was put in before i realized the mistake and finished with almost 6 courts of 15w 40 all the oil was the same...
Looks like i need a new sensor bandit wants $250.00 anyone have any other sources also will attach pics of the number on sensor and on the Perkins motor and it looks like this sensor has been replaced before due to the date on the sensor . It just seems extremely overpriced for a basic sensor .I...
Just changed knives and cleaned everything with gum out carb cleaner/parts cleaner after hearing stories of blades coming loose due to not cleaning threads and dirty surfaces . After doing some research looks like carb cleaner can leave an oily residue do you think this will cause any issues ...
Hey guys. Needing advice. Here in northern Australia. Updating my backup chipper to a late model 18 inch.
looking at two models Vermeer bc1800xl and a bandit 1590xp or possibly the 1890xp hd
Now I’ve never had the pleasure of running bandit. I’ve owned a bc 1500 and a bc1400Xl
Both to your...
Just purchased a used 90xp with the Perkins . The tach goes into test mode each time its started and stuck on hours cannot switch to rpm. The auto feed does not seem to be working right and the tach is IEC . Please advice
Looking at a used bandit 200 in the 90’s
It has a Ford gas motor and looks like it has a crush/lift cylinder with unknown hours and owner does not about past history . It currently does not have brakes and I would add them but it’s unknown what it needs
price is $10,000 and owner seems firm...
I have a bandit 90 and the bolts are shearing or snapping it looks like the blade is hitting the anvil . Did adjust anvil with more clearance and the bearings are only about 1 year old had a friend do them . The previous owner had a blade come loose and they repaired it is it possible that it is...
Good morning folks,
I hope you all had a great Christmas and New Years. I have a project coming up in the next 6 months that I need some wood slivers for. I’ll have a 12” bandit 250xp PTO chipper on a 140 hp Kubota, but as you know . . . our chippers are good at making chips . . . not slivers...
I recently bought a 2018 Bandit 12XP, 100+ hours on it. Two days later upon shutting down it started to squeal. It sounded like the belt slipping. Long story short the chipper drum isn't free spinning, engine pulley won't spin freely even with clutch disengaged. The clutch was never adjusted...
2 Homelite 33cc saws. One is a Bandit, other ZR. ZR runs, Bandit doesn't. What you see in pics is what you get. I used to use the ZR for limbing and pruning. Don't need as I have other better equipment now. The other saw turns over, believe needs a rebuild, didn't really look at too close...
It's time I make the leap. I am looking for a dump truck and chipper of reasonable price and working condition. Bucket/chip combos are a possibility. If you have equipment to sell, send me the information with pictures and we can go from there. Thank you in advance for your responses!
need to replace the disc bearings on 90 xp only one side is bad , its the side near the anvil any tips would be very helpful it almost looks like there is a retaining ring around bearing several small holes but did not seem like there was any allen head inside of it . looked online did not see...
I couldn't help myself when I saw a 2 stroke destined for the landfill, so I snatched it up and took it to the bench. Its a Homelite 33cc Ranger Model UT10947D. After checking things over I fired it up (3 or 4 pulls) and it seemed to run normal for the first couple minutes, I didn't have any...
I am looking at two chippers right now. Hyroller 1200 for $6000 or 2000 Bandit 90 with 1400 hours for $7500. Both disc. Neither have auto feed or hydraulic down pressure. The Hyroller is a rebuild and the Bandit has been owned by a small tree company for 5 years and has been their backup...
have a bandit 90xp with the v465d was running run then shut down it will start then shut down after the key is released , but will run if the key is left in the start position , was going to try a new switch
any thoughts or help ?
thanks for any info
Altec 60' Boom bucket truck
6 speed manual trans
Forestry chip box dump body
2 outriggers
Many updated parts - ready to work
Former Asphlund Truck
Hydraulic Brakes
Bucket plumbed for hydraulic saws
8.1L gas engine
Kubota diesel pony motor
Pintle hitch
Passed inspection 3 weeks ago
7k worth of...
looking at bandit 65 not sure of year but have serial number , the feed tray looks smaller compared to newer bandit 65's the feed springs are different more like a 45 degrees then the new straight vertical springs like the newer ones , the newer bandit 65 with wider tires look much bigger...
Looking for any information on a 20/70 morbark chipper gas 35hp
Especially weight since towing on a smaller truck
Any issues
Thank you for any information
I have a 2005 Bandit Model 280 for sale in Colorado. This chipper does have 4400 hrs but is a tier 3 CAT 135 HP motor and starts and runs great. The hrs are appx. as I still use it somewhat frequently. But we have a grapple truck on the way and do not need 2 large chippers.
Keep the air filters...