carburetor

I have a husky k770 model, rebuilt the carb, gaskets were like potato chips. When starting, it will only start with the choke, pop off the choke and it will rev to full speed and takes a while for it to slow down when releasing the trigger. it also acts like it wants to be a "runaway" engine...

Hey gang! I have a new (2 month old) ms194ce and I've adjusted myself into a hole post muffler mod. The saw has about five tanks through it, and has always had trouble starting. It's only seen motomix for fuel. The saw starts to take on the second or third pull, but when I turn both chokes off...

Hey all, I was "fortunate" to find a Stihl 192TC at a garage sale for $20 recently. Catch was the carb was bad, but the fellow selling it threw in an additional carb (C1Q-S135) and a few other misc parts from another 192TC he had gutted for free. I figured "why not?" For $20 seemed like it...

So I decided to get around to pulling the carb on a nice 011 that I picked up awhile back, in order to clean the carb out and give it a new diaphragm, which I'm fairly certain is all this saw really needs to make it good as new. Cleaning and reassembly of the carb went just fine. The old...

Hello all, Im currently cleaning up a little Homelite Bandit LX-30 - I dont have many plans for it other than id just like to get it running and functional - Everything is in good condition, Im just in need of a new carb for it (Screw holes stripped unfortunately) - And then the black Heat Dam...

I see there are several superceded part numbers for the Dolmar/makita carburetor for 6400/6401/7900/7901 ext series of saws, the newest one is some Zama that places want like $130+ for....yikes...I can't seem to find cheap aftermarket replacement carbs for this saw after searching for a bit, its...

Anyone in the know want to comment please? I have it torn down to this point (see photos) ultimately I need to get to the fuel reservoir to inspect and possibly repair/replace gasket as it is leaking just sitting on a table. This is the primary reason for teardown. Also going to rebuild carb...

Hello experts! Brand new to this site. I’m a small engine tech and I’m working on an echo cs 600p. The owner said while operating it that the rpm’s began to race and it wouldn’t shut off. After getting it to stop he restarted it and it would idle but cut out after the throttle was applied. I...

I got roughly 40-45 used zama, tillitson, and Walbro carbs... all are oem, and were purchased with the original saws that are now being parted out. Those saws include (but not limited to): 009,011,020,024,026,028,028 super,031,032,034,036,044,066, 064, and 08 s.. most just need new gaskets and...

I have wasted a good bit of time trying to rebuild carbs for two 18" Craftsman Chainsaws. I have decided to start from scratch and buy new carb kits for both, but I have now learned the hard way that there seem to be a million different configs and part numbers out there. #1 is Craftsman Saw...

I see in 2010 Nethercutt had this issue and a new gas line fixed his problem. Unfortunately, it didn't work for me... My inherited 039 ran fine for 2 years, then developed the issue of venting fuel out the tank at high rpm. I've changed the vent line, fuel line and installed a new carb kit...

Hi ya all. Been reading for quite a while, decided to join and post. I bought a MS361 kit and a couple extra cylinder kits to try my hand at porting and modding without spending Stihl dollars. All just for the fun of it! I'm on about my fourth iteration of top end builds, and I gotta say I love...

FREE!!!! Echo CS-6700 parts saw. Things I know are wrong with it are bad piston, but cylinder is still ok. Also not getting spark. See pictures for detail, or ask questions, I'll try my best to answer. JUST pay to be shipped from 30205.

I got my hands on a Stihl 025 cheap as a non-running saw. I do not have a compression tester, but it feels right and I have owned an 025 in the past, replaced it with an MS250 and now bought this one as a back-up saw. I think I am acceptable on compression, but please correct me if that is a...

My grandpa had a Poulan Pro 205 that sat in his garage for years unused due to a broken starter pulley that he never replaced. He gave it to me and I replaced the pulley and had it running. Decided to take it all apart and give it a good cleaning. I opted to use Fuel resistant permatex in place...

Hello all, I am at a complete loss- my Husqvarna 394 chainsaw will start but immediately dies. It is a 1998 model. I have already tried the following: New Gas line New Fuel filter New Fuel tank vent New tank vent filter New Gas cap Put carb kit in it Cleaned the carb Air filter is...

Hi.I have a Husqvarna 236 recently rebuilt, but i have an issue.Saw starts only with choke once it's hot.Should i tune the carb again?Wich screw?

Hi, I recently acquired a 1960's Asplundh Whisper Chipper. It is powered by a Ford 300 I6. It was equipped with an Holley 1949 single barrel carburetor (1 5/8 bore w. 3" bolt centers). The carb is trash corroded beyond rebuilding. I have seen Ford 300's fueled by Autolite 1100's, Carter YF...

I am confused. The service manual for Stihl 031 diagram shows the H and L and Idle as follows which doesn't make sense. My common sense tells me in the diagram the H screw should be #3 and closest to air filter, the L screw should be #1 and closest to engine, and the idle screw is #2 the...

So I just replaced the piston and cylinder on my 051AV (early model) and I'm trying to get the carb (Tillosten) tuned. After the replacement, the saw fired right up and idled well, but the first time I pulled the throttle, the carb got stuck open so I pulled the carb off and cleaned it and it's...