Anyone know the Part # for the extended chip deflector 066 046 etc

[Freakingstang]

Hey guys, I checked my dealer and he is amish without computer access. He knew there was an extended chip deflector, just couldn't find the number quick. I told him not to worry, I would get it. lol. Any help guys?
Should be the same for an 044 046 and 066 and some others, goes on the clutch/bar cover and deflects the saw chips downward.

Thanks
Steve

 

[bump_r]

I've got the IPL, just not with me. If no one replies with the # soon, I'll grab it up.

 

[Freakingstang]

Thanks Bob

 

[NWCS]

if its the extended rubber flap your after, the PN is 1122 656 1510
the clutch side cover itself is 1122 648 0401

 

[Lakeside53]

Hey guys, I checked my dealer and he is amish without computer access. He knew there was an extended chip deflector, just couldn't find the number quick. I told him not to worry, I would get it. lol. Any help guys?
Should be the same for an 044 046 and 066 and some others, goes on the clutch/bar cover and deflects the saw chips downward.

Thanks
Steve

It only works with the wrap side cover though...

 

[Freakingstang]

It only works with the wrap side cover though...

Why is that? I was going to put it on my 066 for milling and felling duties. I like the husky longer chip deflectors....

The cover looks the same from Pics I looked at......

 

[Lakeside53]

Why is that? I was going to put it on my 066 for milling and felling duties. I like the husky longer chip deflectors....

The cover looks the same from Pics I looked at......

.. but I can't see the picture you are looking at!

The wrap side cover is about 1 1/2 inches deeper than the non-wrap cover. I goes all the way to the bottom of the saw. The big rubber defector won't lock into the small side cover. Maybe you already have the wrap cover?

Put on the tank protector 1122 351 0901. Only about $5, but will stop a bad chain throw from punching the tank.

 

[Freakingstang]

Thanks, I'll check out the numbers I have on my cover and see what I've got.

 

[fishhuntcutwood]

Thanks, I'll check out the numbers I have on my cover and see what I've got.

Here's a pic of the full wrap cover Andy is talking about. It's got a flare to it. Pretty easy to spot. It'll fit the 440, 460, and 660....and the 361 with some Dremel work!

http://www.arboristsite.com/attachment.php?attachmentid=29960&d=1136522864

 

[Lakeside53]

Here's a pic of the full wrap cover Andy is talking about. It's got a flare to it. Pretty easy to spot. It'll fit the 440, 460, and 660....and the 361 with some Dremel work!

http://www.arboristsite.com/attachment.php?attachmentid=29960&d=1136522864

Wait - Don't dremel for the 361... The 441 wrap cover fits it... available in a week or two for $38 list!

 

[fishhuntcutwood]

Wait - Don't dremel for the 361... The 441 wrap cover fits it... available in a week or two for $38 list!

HA! No, I Dremeled an old 660 full wrap cover...not the saw! Just a little bit off the top, and a tad behind the dog.

 

[fishhuntcutwood]

... available in a week or two for $38 list!

It's a flared, full wrap model that takes the deflector? Got a P/N for me?

 

[Lakeside53]

It's a flared, full wrap model that takes the deflector? Got a P/N for me?

1138 648 0400 (cover) and 1138 656 1500 (Deflector).
These go with the factory wrap handle that will be available on the 361 soon...

Don't tell anyone else