Want to Sell Husqvarna 2100/2101 parts

[epicklein22]

Husqvarna 2100 being parted out. It had an air leak/carb issue when I bought it, but did run. Upon further inspection, someone seized the saw up at one time, cleaned it up some and slapped it back together. It had 150lbs compression, but piston and cylinder were roughly obviously. I've decided to part it out instead of repairing it.

Crankcase, in good shape, bearings are worn out.
$40



Fuel/oil tank, nice shape
$60



Full wrap handle, good shape, will come with the brackets
$50


Ignition, was running when torn down.
$60


Cylinder, has issues around intake and transfers, but you might be able to use it by lowering the intake some. Exhaust side looks fine.
$20


2 top covers, both in nice shape, small crack in one filter cover, but not bad at all.
$50 for each one

Muffler and cover, the cover mounts have been brazed, muffler has a hole cut in it and baffle is broken. $10

Side cover, nice shape
$30

Bucking spikes, nice set
$20

Crank and bearing, both in nice shape
$50

 

[epicklein22]

Starter, $35

 

[tpope]

I want that cylinder

 

[R2D]

And I'll take the rest.....can't shake the 2100 bug : (

 

[epicklein22]

Sold the rest of the lot to R2D.

 

[redfin]

R2D, can you live without the handle?

 

[R2D]

R2D, can you live without the handle?

Let me have a look at it first. If i keep it, I got another I'd let go. Just building a super nice one.

 

[redfin]

Good deal man, drop me a note.

 

[gulity1]

Redfin what are you looking for on the 2100

 

[redfin]

Full wrap.

 

[Marshy]

Anyone willing to part with one of those cylinder shrouds and filter cover PM me please.

 

[Roll Tide]

I'd like to find a crank for a 2100 pm me

 

[R2D]

After I'm done with my builds, I will have lots of parts left over to sell. Crank and cylinder shrouds will be available. Filter covers....not so much. Those things are a pain to find in good shape.

 

[ChoppyChoppy]

View attachment 410656 View attachment 410657 View attachment 410658 View attachment 410659 View attachment 410666

Starter, $35

none of your pics load up. But I could use the starter if it's in good shape.

 

[epicklein22]

none of your pics load up. But I could use the starter if it's in good shape.

I had to carry them over to the next post. All the parts are headed to r2d later today.

 

[Sparkysparks9]

After I'm done with my builds, I will have lots of parts left over to sell. Crank and cylinder shrouds will be available. Filter covers....not so much. Those things are a pain to find in good shape.

Just bought a 2100, and found it needs a new crank. Runs great...but a bit of noise. Took the cylinder off, and seems to have a bit too much play in the bottom end. Was hoping they were rebuildable, but apparently not? So in short, if you end up with an extra good crank...you have a buyer...thanks !

 

[Marshy]

Just bought a 2100, and found it needs a new crank. Runs great...but a bit of noise. Took the cylinder off, and seems to have a bit too much play in the bottom end. Was hoping they were rebuildable, but apparently not? So in short, if you end up with an extra good crank...you have a buyer...thanks !

All the parts were sold. Do you know if it needs new crank shaft bearings or does it need a lower rod bearing? The crank bearings are replaceable FYI.