Helllo, I recently purchased a 252 and noticed what seems to be a lot of play on the top portion where the engine sits( swing arm?). when i am on the way across someones yard to a stump, the whole top portion sways back and forth quite a bit, and was wondering if this was normal or not. i looked underneath where the hydrolic piston is mounted and the nut seems tight but seems to have some play. Also i noticed the drive chain was very loose so i tightened it up some but not sure how much play to leave in the chain. sometimes the chain seems tighter than other times? Any help would be greatly appreciated. any other info on what i should do for matinance on a used machine is great as well, i will be changing the oil( 10w-30 synthetic?) or non synthetic? engine is a 2012 27hp kohler 391 hours.
Need advice on a recently bought 2005 vermeer sc252
- Thread starter jaystihl
- Start date
Help Support Arborist Forum:
Hi Jay,
There should be a king pin and bushings on the grinder that have gone bad and that's why the cutter wheel head is sloppy. Look at the base of the swing arm and you should see a bolt or a pin that ties in with the swing arm. You'll have to replace those parts. Either type of oil will work. Keep the cutter wheel bearings greased and watch the air filters as grinders do create a lot of dust. Make sure to grease the other fittings as well.
Hope this helps!
Dave
Global Equipment Exporters
770-420-6400
There should be a king pin and bushings on the grinder that have gone bad and that's why the cutter wheel head is sloppy. Look at the base of the swing arm and you should see a bolt or a pin that ties in with the swing arm. You'll have to replace those parts. Either type of oil will work. Keep the cutter wheel bearings greased and watch the air filters as grinders do create a lot of dust. Make sure to grease the other fittings as well.
Hope this helps!
Dave
Global Equipment Exporters
770-420-6400
Thanks eq, and marne, just noticed today i hit a old telephone cable, and it looks like it got underneath the grease boot on the cutting wheel shaft and pulled the boot out. is this fixable? maybe i can push the boot back in? Felt like it was pretty hard. looks like this is the joys of owning a stumper, Ha!
marne
ArboristSite Operative
- Joined
- Feb 20, 2014
- Messages
- 148
- Reaction score
- 56
Put in a new grease nipple, keep spare nipples with you.
A stumper needs endless and repeating hours of care, tensioning, greasing, adjusting, replacing, welding, sharpening, oil changing, searching buying.
That's just why many companys don't own one and secialised grinding companys exist.
After I knew what it means to own, operate and maintain grinders, I could never ever anyone else operate one of my machines. It is really different from a mower, a chipper or car.
A stumper needs endless and repeating hours of care, tensioning, greasing, adjusting, replacing, welding, sharpening, oil changing, searching buying.
That's just why many companys don't own one and secialised grinding companys exist.
After I knew what it means to own, operate and maintain grinders, I could never ever anyone else operate one of my machines. It is really different from a mower, a chipper or car.
CalTreeEquip
ArboristSite Guru
About the excess play. Determine if the slop is in the pivot bearing or the control arm bushings. There are four bushings and if they are all worn then there can be quite a bit of play.
Generally don't run synthetics.
Chain should be taut but not overly tight. Grease it with chain lube.
Not sure what you mean my a "grease boot". There is a grease seal on all the bearings. If you tore that out you'll need to replace the bearing. I don't know of any boots on these things.
Go to Vermeer's website and register your machine with them, they will send you an owners and parts manual for it free of charge.
Generally don't run synthetics.
Chain should be taut but not overly tight. Grease it with chain lube.
Not sure what you mean my a "grease boot". There is a grease seal on all the bearings. If you tore that out you'll need to replace the bearing. I don't know of any boots on these things.
Go to Vermeer's website and register your machine with them, they will send you an owners and parts manual for it free of charge.
Thanks for all the help cal. i purchased some green teeth tonight, but have a really hard time finding the replacement 3rd wheel(steering). and also want to see how much the addintional bolt on wheels(2), to make four wheels in front for more stability. Hopefully vermeer will send me a parts manual with those in there as you stated earlier. Its crazy how many of these machines are out there and so hard to find parts!
OLD MAN GRINDER
ArboristSite Operative
Just a personal preference for me I use Castrol 10/30 full synthetic in all my ztr's and stumpgrinders after the initial 50 break in hours..
Bob.....
stumper63
ArboristSite Operative
Parts are not hard to find for a 252, you just have to get them from the nearest Vermeer dealership. The dual wheels are sold in pairs from Vermeer and are about $250. I guess you're in Florida so maybe its always flat, but I would recommend always using them, especially if you're new to grinding. The steering wheel tire and wheel is about $50 if I remember correctly. I've had several over the years.
Stumper63
Stumper63
stumper, does the extra wheels up front make a big difference when you still only have the one wheel in the back. It is flat in florida except for lots being built up more and more from hurricane/flooding. only had the grinder a week and was going across a slight embankment, you guessed it , rolled the damn thing right on its side. luckly no damage, just had to clear oil out of cylinders and buy new air filters.
066blaster
Addicted to ArboristSite
I used mine once without the duals. I had to get though a gate. It was scary. It makes it alot more stable with duals. No worries at all, about tipping.
marne
ArboristSite Operative
- Joined
- Feb 20, 2014
- Messages
- 148
- Reaction score
- 56
I found it's harder to steer with the duals, when u got a sharp turn with em on, you can still unlock one drive wheel, than it works perfect.
It seems that for some reason, that while grinding the machine is sitting heavier on the ground, when having the duals on.
The wheels are on in maybe 40% of my jobs, these can't be done without em, while here everything is so tight, that leaving em off is also a must very often.
Just buy em.
It seems that for some reason, that while grinding the machine is sitting heavier on the ground, when having the duals on.
The wheels are on in maybe 40% of my jobs, these can't be done without em, while here everything is so tight, that leaving em off is also a must very often.
Just buy em.
Think i am definatly going to by them. As far as steering goes, (i only have a single wheel in back), i can't seem to steer worth a darn! dont think i have the original tire on , but the machine seems to drag or push the steering wheel. tried putting a bigger tire on and it was worse. Any suggestions? just crazy that you have to constantly lock and unlock wheels just to steer.
066blaster
Addicted to ArboristSite
I don't unlock the wheels ever. Just go forward and Back to get the thing pointed where you wanna go. They don't steer that great that's just the way they are.
066blaster
Addicted to ArboristSite
I can measure tomorrow its a my shop. I think less than 4 foot. I will check tomorrow though.
066blaster
Addicted to ArboristSite
It's 44 inches wide with the duals. 48 inch trailer would work fine
Similar threads
