Some months ago, I found a good looking and running MS 200T. The seller said everything was working fine, but it would just shut off after a while. Compression was okay, bit on the low side for my liking, but 140 psi is still decent, right? So I made my balkanese ancestors proud, and haggled him down from 250 to 200€. Figured an ignition would cost around 60€. I think the saw sat for some years in a shed. Pretty much every rubber part was stiff, shrunk, brittle or all at once. So i decided to change pretty much every bit of rubber in the machine. I have another two 200Ts waiting to be rebuild, so I figured I save some time and make a shopping list that I can reuse. And now you can too:
Some stuff is redundant. E.g. the gaskets and seals and the impulse hose. The fuel/vent line comes with the "connector".
If I missed something, or made an error, please comment, so I can fix it.
Hope this helps someone.
Set of gaskets (oil, block, cyl, ex) | 1 | 11290071050 | € 24,20 |
Oil hose | 1 | 11296479400 | € 3,60 |
O-ring fuel cap 25x3.5 | 1 | 96459487734 | € 0,70 |
Fuel filler cap | 1 | 3500520 | € 6,40 |
O-ring oil cap 23x3 | 1 | 96459482470 | € 0,60 |
Oil filler cap | 1 | 3500510 | € 5,10 |
Fuel/Vent Hose (new style) | 1 | 11293503600 | € 5,50 |
Tank vent (new style) | 1 | 3505802 | € 3,30 |
Manifold | 1 | 11291412200 | € 30,70 |
Impulse Hose 1m | 1 | 9302803 | € 2,60 |
Hexagon nut M5 | 2 | 92162610700 | € 0,40 |
Air filter, fleece | 1 | 11291201607 | € 6,00 |
Foam insert | 1 | 11291220100 | € 1,40 |
Annular buffer (upper) | 1 | 11297909900 | € 5,50 |
Annular buffer (lower) | 1 | 11167909600 | € 6,90 |
Annular buffer (rear) | 1 | 11297909902 | € 5,30 |
Tension spring | 3 | 9975515 | € 0,80 |
Piston Ø 40mm | 1 | 11290302002 | € 35,10 |
Pistonring Ø 40x1.5 mm | 2 | 41190343003 | € 7,70 |
Needle cage piston 9x12x10 | 1 | 95120032030 | € 6,50 |
Roller bearing 12x24.5x8.8 | 2 | 95310030105 | € 9,60 |
Worm 0.325" 7T | 1 | 11296407105 | € 4,40 |
Chain sprocket 0.325" 7T | 1 | 11296402004 | € 19,30 |
Impulse Hose 102mm | 1 | 11291418600 | € 2,30 |
Connector | 1 | 11293581902 | € 2,30 |
Air filter | 1 | 11291201602 | € 6,80 |
Bumper strip | 4 | 11236486600 | € 1,40 |
Pickup body | 1 | 3503504 | € 6,10 |
Cylinder gasket | 1 | 11290292303 | € 2,30 |
Exhaust gasket | 1 | 11291490600 | € 1,50 |
Oil seal 12x20x5 | 2 | 96400031191 | € 10,00 |
Ignition module | 1 | 4001306 | € 61,10 |
| | | |
Puller Flywheel | 1 | 11168930800 | € 9,00 |
Press Sleeve Oil Seals | 1 | 11298932400 | € 5,00 |
Sleeve Oils Seal Clutch Side | 1 | 11298934600 | € 16,20 |
| | | |
Tool kit | 1 | 11298901400 | € 13,50 |
Chain scabbard | 1 | 7929128 | € 4,00 |
Some stuff is redundant. E.g. the gaskets and seals and the impulse hose. The fuel/vent line comes with the "connector".
If I missed something, or made an error, please comment, so I can fix it.
Hope this helps someone.
