dolmar

I have a Makita DCS-6800i (same as Dolmar PS-6800i) with a badly scored cylinder. I can find replacement pistons, but not a good cylinder. It's a 68cc motor with a 49mm diameter piston. Does anyone know if I can switch the cylinder & piston out to a 50mm diameter? There are many 50mm sets...

Part Number: 119130001 Qty: 05 Pcs left Location: Near Equator -oldpartsinasia Joe

Selling my stock of Makita/Dolmar parts. Built a few of these saws before, and held onto these parts in the thoughts that I would build another. Well I have yet to do so with getting involved with machining and starting the shop here the last few years. Figured someone has has more utility in...

I'm looking at light alternatives to a 372. I can get a 2083 or 7900?

This is my first proper build, I've done a couple of drill through the muffler type muff mods and a fair bit of saw tuning and repair. Bought this 341 for £20, wouldn't run. Bad fuel line. Snipped the bad bit out and bodged it back together. It ran well then. Next, muff mod. I'll let the pics...

Dolmar Crankcase clutch side half(both the same) 024 111 018 -$35 ea Dolmar 309 and Master clutch cover- $30 ea. Dolmar starter covers (left)- R. 144.112.091 (right) R. 122.112.011 $20 ea. Sachs dolmar starter covers- $20 ea. Dolmar top cylinder cover and air filter cover- $20 for the pair...

Have 1 last set of Cylinder CPL for Dolmar 343 Happy Start. 01PC 031130150 Dolmar 343 (Diam 55) 01PC 001131150 Decompression Valve is also available on request. note that the piston coating appears to have discoloration over the years. Interested party please reach out to me...

Hello. I have found a Dolmar 113H and on it there is a guidebar (3/8 .058 72drives) with these markings: 124 Dolmar Sachs 411910650. This seems to be the original guidebar that came with the saw but according to owner manual it's not the right one. Can anyone with more knowledge on vintage...

Interested check, people! Limited qty, NOS 030 111 210 Crankcase Clutch Side 030 111 060 Crankcase Magneto Side -oldpartsinasia Joe

*Interest check for a NOS Piston for Dolmar 116* (not Dolmar 116si, but for Dolmar 113/116 series) 114 132 101 Piston Assy 45mm Single Piston -oldpartsinasia Joe

Hi All, I am writing in hopes of some expertise on a Dolmar PS 7900 advanced timing set up. I have a PS 7900 which was build by a gentleman who has passed away so I cannot go back to him for help. Here is what I have been told has been done to it. Finger ports, 272 coil, opened up muffler...

Interest check! 024143020 Ignition coil for PS9000/PS9010 (for non-US/Non-AUS) I might have a couple new ones in stocks (on paper). Someone needs to say "hey I might need one" > I will go check > a nice photo might appear. No pics, no count.

Hey people, happy to find a site that lots of buzz on chainsaws. If you have really old Dolmar Chainsaws and want to search for that elusive part, PM me the 9 digit Dolmar Part number and I will check if we have such DOLMAR part numbers in our stock. The old parts are not in US, but in...

I’m after an air kit for my Dolmar. I’m installing a 7900 piston and cylinder and want to put a filter kit on it as well. I know about the HD filter kit from Sawagain.com but want to know if there are any other alternatives. Possibly if I can buy just the intake elbow and clamp on a different...

I picked up a mint Dolmar 5100 yesterday that does not have the metal ring insert for the carb intake boot. I've searched everywhere on the internet and I cannot for the life of me find one available. Does anybody have a contact or source where I can pick one of these up? If there are truly...

Well the wife will not be happy with me but i bought two MCV51’s that were brand new in box from 2012 that were lost in a saw shops inventory. Made in Germany by Dolmar with almost consecutive serial numbers!

Kinda hate to sell it but it’s time to put some cash away. Price is $650.00 Very very nice saw with brand new big bore kit done nicely. Saw runs very well and extremely strong. Only a few tanks on this since rebuild. 54mm @ 85cc. Saw has brand new oem clutch cover, brand new oem fuel tank and...

I see there are several superceded part numbers for the Dolmar/makita carburetor for 6400/6401/7900/7901 ext series of saws, the newest one is some Zama that places want like $130+ for....yikes...I can't seem to find cheap aftermarket replacement carbs for this saw after searching for a bit, its...

Looking to buy a 7900 or 7901, but will look at anything from this family of saws 64cc and larger. Shipping to 48642. Prefer PHO. Venmo or PayPal. Thanks.

Hey friends, couple questions regarding the mentioned saw. Can i upgrade it to .325 ? How well does this saw respond to a muffler mod? I would most likely enlarge the existing outlet but not quite sure how much. What would be the meanest chain for that saw in 3/8 lp pitch? At some point this...