help

Hi, I’m now on getting a spark from my danarm 55 I’m trying to restore. I think it’s the ignition coil and when I pulled off the wire cover I don’t think the positive was connected. Can someone please help with how it should be wired or where I can buy a replacement because I’m pretty sure it’s...

Hi, I've got the chance to buy a Danarm 110 in pretty good condition it seems (pictures attached) the guy wants £90 that includes some equipment. is this low, high? I can't seem to find a definitive price. Thanks

I’m sure everything I’m going to ask has been hit before but I have searched for quite awhile on here through bad threads that won’t show up and also pictures.. purchased a 440 for $50 I am going to do some mods to it, dp muffler and cover, new piston and jug.. Id like to port out the ridges a...

hello all, i was recently given a 48" cannon bar. it used and probably 10 years old but its in fine shape. it is marked "HUS5063 S" i dont know if this means i need to run 063 chain or not. its for milling mostly and accational stump job, if you understand these markings please help. thanks

Hey guys I'm rebuilding an ht 75. The engine is all together and it runs fine but it won't turn off. I just replaced the spring in the grip that should ground it out, and from what I've seen everything running from the engine to the tip of that spring works fine. What I can figure out is how the...

I have a ms440 that has good compression (just put a new piston in it), spark, just put a new fuel line in it etc. After I let it sit for a while, it will start briefly on full choke then die, after that when I pull it over, it just fires and jerks my hand back. Any thoughts would be...

Ok so yesterday I updated my 12 yr old woodmaster 4400, fan is new, ETC is updated(if anyone else has done this, they know the wiring has changed some), snap disc replaced. Temp is reading, there are no codes showing up now that I'm up to temp but my fan is still not kicking on. I've gone...

It’s a 372 clone build. It recoiled when I first built then the rope broke. Replaced that and the spring was chinsy so I replaced. Now the dang thing won’t retract. It retracts off the saw just not installed against flywheel. Any suggestions or advice is welcome. At my wits end with this...

555 Or 562XP Yes, I know this one is a dead horse but I have a few questions. I currently have a 435, which I pretty much destroyed cutting 9 cords of oak with. That was my first saw and I learned a lot of things, especially what not to do. I bought that saw knowing this and now I ready to...

Hello All, Seeking your experienced counsel. Please review this photo and advise me how you would piece this tree out. I will be using my bucket truck with a 52' working height. (I am guessing the tree to be 60'?) Since I have bid it out, I have lost sleep over this one...just want to be wise...

I have a 1990xp bandit chipper recently it has not been working correctly all of a sudden I will try and chip something I would lose rpms and it wouldn’t regain rpms I would have to push the button and try to regain rpms sometimes it would go up and sometimes and wouldn’t at all my rpms would be...

Hello all, new user to the site, have lurked some forums. What a great place. Lots of helpful advice and tips. Little back ground. Husqvarna 254 professional serial number 8180663, I seem to have a dead coil. Saw is ancient but I love it. It rips! Compression check 130 psi cold 145ish...

We bought this house a year ago and my tree looked like this. We found Japanese beetles and started spraying for them last year. We will continue this year. Is that what caused this? Can I bring this tree back?

Stihl MS291 has me baffled. This is the chain: STIHL 3689 005 0081 Oilomatic 26 RM3 81. I have sharpened countless chainsaws in my life using nothing but a file and I have never had a problem until I purchased this saw. I am doing everything right. I am holding a 3/16 file at a 30 degree angle...

Hello, Stihl MS291 has me baffled. This is the chain: STIHL 3689 005 0081 Oilomatic 26 RM3 81. I have sharpened countless chainsaws in my life using nothing but a file and I have never had a problem until I purchased this saw. I am doing everything right. I am holding a 3/16 file at a 30 degree...

I've been searching the forum all morning and found a huge amount of really useful information, but so far no answer to the question I came here looking for. Maybe someone can end my agony, haha. I was recently gifted a Stihl Wood Boss 028 AV that was leaking bar oil. So I tore it down and...

Hey Fellers, I go by axe, I’m 27, I’ve been doing tree work since I was 18. I started dragging brush and humping logs for the first 2 years. Then taught myself to climb from untying my bosses knots. Long story short I still use simple monkey knot, running bowline, and Clove hutch. One rope...

I'm just curiozc why my Blake's hitch is so hard to move around in the tree with. I see people swing around and land on other branches but I weigh 140 and have to really put m weight into it . And also my line will only be touching one branch but the friction makes it more difficult. My boss...

Hoping the collective knowledge here can point me in the right direction. WeWhave a tree in our yard that i believe is a Shumard Oak. It looks fairly healthy with the exception of the leaves at the very very end of many branches are starting to curl up and shrivel (see pictures). The home was...

picked up a bandit 65 serial # 004976 , going replacing the motor and all the original wiring to tach is cut up and spliced everywhere , looking for a wiring diagram for chipper , also looks like some wires have been cut from some type of hydro solenoid towards the back of machine , thanks for...