Want to Buy Case Splitter for Stihl

[angelo c]

AND HUSQVARNA TOOLS with prices

Those are fairly reasonable prices for service tools.

 

[drf255]

pantelis is sending me somedrawings of the stihl splitter.

If you post the pics and measurements it would be helpful.

I'm NOT looking to go into business, but I could price the materials and make some up. Would only want to do a few and sell to members at my cost. Would keep one for me

Those look like they'd cost around $30-40 to make, maybe less.

I'm wondering if it would be easier to make with 1/4" stock. Use a long adjusting nut with some threaded rod, then make the split to go over the crank out of a half piece of tubing.

What's the width of the opening of the tool?

 

[tntblaster14]

Yea I think I'm just going to go w/ the factory tools for crank splitter.. pretty reasonable IMO.. the homemade ones I saw here so far are pricing right about the same $$ too.

 

[Derrick Sawyer]

My dealer sold me the Husqvarna splitter for $80, they said they use it on almost everything husky and stihl, works fine but as some said to put back together to get things lines up and slowly turn the case bolts evenly, whereas the stihl splitter can put back together, the stihl clutch side splitter on ebay can be had from the UK for 100+20 shipping, not bad, heres the link, plus you know you'd be able to sell the stihl one for as much as you paid down the road if you need to. I didn't have time to build one with angle iron, drilling holes for bar mount studs, and a center hole to put the center bolt from one of my automotive steering wheel pullers to mount onto.

http://www.ebay.com/itm/Genuine-Sti...arts_Accessories&hash=item35d3fcaaf0#shpCntId

 

[drf255]

I could easily see making the splitter "H" shaped. Make the top part the case compressor and the bottom the splitter.

May get bulky though.

If someone can post some dimensions it would help.

 

[treesmith]

Bought the husky one from tlandrum and the stihl from ebay, should cover everything
I can take measurements when they arrive

 

[Derrick Sawyer]

Imagine this steering wheel puller mounted on angle iron with holes drilled in, the center is threaded for the long bolt, which you would turn to engage the crankshaft end, even has the cone shaped center punch adaptor, and you can use the sides to secure it to the angle iron, which is bolted onto the bar studs, may need a couple sets of bar nuts to get the spacing right:

 

[pantelis]

If you post the pics and measurements it would be helpful.

I'm NOT looking to go into business, but I could price the materials and make some up. Would only want to do a few and sell to members at my cost. Would keep one for me

Those look like they'd cost around $30-40 to make, maybe less.

I'm wondering if it would be easier to make with 1/4" stock. Use a long adjusting nut with some threaded rod, then make the split to go over the crank out of a half piece of tubing.

What's the width of the opening of the tool?

The husky splitter is easy to make , the stihl is a little complex better must find the oem and copy it , from drawings or dimensions is very dificult to make this tool.

 

[pantelis]

Bought the husky one from tlandrum and the stihl from ebay, should cover everything
I can take measurements when they arrive

Yes the stihl splitter its a fantastic tool, can open and close the case of about all models

 

[pantelis]

My dealer sold me the Husqvarna splitter for $80, they said they use it on almost everything husky and stihl, works fine but as some said to put back together to get things lines up and slowly turn the case bolts evenly, whereas the stihl splitter can put back together, the stihl clutch side splitter on ebay can be had from the UK for 100+20 shipping, not bad, heres the link, plus you know you'd be able to sell the stihl one for as much as you paid down the road if you need to. I didn't have time to build one with angle iron, drilling holes for bar mount studs, and a center hole to put the center bolt from one of my automotive steering wheel pullers to mount onto.

http://www.ebay.com/itm/Genuine-Sti...arts_Accessories&hash=item35d3fcaaf0#shpCntId

this splitter its super, open and close the cases of about all stihls models no need to sale it

 

[Toad22t]

I bought my clutch side factory stihl splitter of an international seller for 103 shipped. It just took a week and a half to get here.

 

[Toad22t]

Seller was kwikchip and sorry it was 103 +20 shipping.

 

[Stihlofadeal64]

Seller was kwikchip and sorry it was 103 +20 shipping.[/QUOTE

Looks like the like above, correct?

 

[treesmith]

Same, kwikchip but $125au + $25au shipping

 

[tntblaster14]

I went ahead and ordered one of these... According to my local Stihl dealer.. this tool will not split cases... just mount... everyone else says it does both... which is it?

 

[pantelis]

I went ahead and ordered one of these... According to my local Stihl dealer.. this tool will not split cases... just mount... everyone else says it does both... which is it?

the stihl clutch side splitter can open and close the crankcase
the stihl flywheel side splitter can open and close the crancase
the husqvarna splitter can only open the crankase
i hope i help you

 

[angelo c]

I went ahead and ordered one of these... According to my local Stihl dealer.. this tool will not split cases... just mount... everyone else says it does both... which is it?

Ask him what he uses then....cause its NOT the Stihl tool then...

 

[pantelis]

Ask him what he uses then....cause its NOT the Stihl tool then...

he uses stihl but the big mamma say dont sale to customers.

 

[hseII]

STIHL PART NUMBERS TOOLS
0000 850 1300 * Pressure/Vacuum Pump
2 0000 855 8106 Sealing Plate (qty 2)
1 0000 855 9200 Adapter Nipple
0000 893 4105 Chain Identification Gauge
0000 890 2201 Installing Tool (large starter rope bushing)
0000 893 2600 * Piston Ring Clamp
0000 893 5903 Locking Strip (14 mm angled spark plug hole)
0000 893 5904 Locking Strip (10 mm spark plug, 2-cycle only)
0781 120 1111 Lubricating Grease (seals, sprockets, etc.)
0781 957 9000 OH 723 Lubricating Fluid for Rubber Parts
0812 540 1112 **Hex drive small shank T 27
1106 890 4501 Flywheel Puller
1108 893 4800 * Piston Holder (wooden block)
1110 890 4500 Flywheel Puller
1117 890 0900 Chain Brake Spring Tool
1118 850 4200 Flange Adapter
1119 850 4201 Flange Adapter
1122 145 1200 Exhaust Port Block Off Adapter
1123 851 8300 Sleeve (qty 2)
1123 855 4200 Flange Adapter
1124 893 7100 Sleeve (qty 2)
1127 851 8300 Sleeve (qty 2)
1138 890 1200 Flange Adapter 1138
1139 893 2500 Flange Adapter 1139
1140 890 1200 Flange Adapter 1140 (added 4-2010 for pressure test 1140 series)
4118 890 6401 Setting Gauge
4133 893 0800 Flywheel Puller 1132, 4137
4140 145 1200 Exhaust Port Block Off Adapter for 4137, 4140
4180 893 6400 0.1 mm Valve Adjustment Gauge (STIHL four-stroke engines)
4221 025 2200 Decompression Valve Plug
4221 893 5900 Locking Strip (14 mm, straight spark plug hole)
4282 890 2700 10 mm Piston Stop (STIHL four-stroke engines)
5910 850 0300 * Leak Down Tester (for any four-stroke engine)
5910 850 1009 * Tachometer
5910 850 4200 Flange Adapter (replaces 1128 850 4200)
5910 850 4503 * ZAT 4 Ignition Spark Tester
5910 855 4201 *** Ex Flange Adapter (new for 4144, 4241 1141, and others)
5910 890 0400 Mandrel for 2" Abrasive Disc
5910 890 2301 * T-20 Screwdriver
5910 890 2304 ** Square end WALBRO carb adjust screwdriver
5910 890 2305 * Screwdriver (orange long carburetor adjust)
5910 890 2306 ** Screwdriver 2mm hex tip (1141 series carb adjust)
5910 890 2307 ** 4mm screwdriver
5910 890 2415 * T Handle T-27 X 200mm
5910 890 2420 * T Handle 8mm X 200mm
5910 890 2800 Clutch Spring Assembly Hook
5910 890 4500 Limiter Cap Tool
5910 890 4501 Limiter Cap Tool
5910 890 4502 *** Limiter Cap Tool (1141 and others)
5910 890 4504 *** Flywheel Puller (replaces 1135 890 4500)
5910 890 8600 Flywheel Blocking Tool (STIHL four-stroke engines)
5910 893 0300 Rewind Tool
5910 893 0800 Flywheel Puller 4140, 4144
5910 893 0801 Flywheel Puller 1123, 1127, 1130, 4241, 4282 (replaces 1116 893 0800)
5910 893 1100 Long Mandrel for Abrasive Pad
5910 893 1702 Bushing (replaces previous bushing 0000 963 1008)
5910 893 5601 2" Abrasive Disc (pkg qty 10)
5910 893 5602 1" Abrasive Pad Medium (pkg qty 10)
5910 893 5603 3/4" Abrasive Pad Medium (pkg qty 10)
5910 893 5604 1" Abrasive Pad Extra Fine (pkg qty 10)
5910 893 5607 3/4" Abrasive Pad Extra Fine (pkg qty 10)
5910 893 6600 Setting Disc for Small Screwdriver
5910 893 8800 * Pick-Up Hose Hook
5910 893 9600 *

You are now on the Christmas Card list.

 

[pantelis]

You are now on the Christmas Card list.

i have the christmas card list husky and stihl