Sold Crusty 395 XP Husqvarna Builder

[chipper1]

Grabbed this up with the intention of getting it going to mill a large white oak at my parents place. As so often happens another saw happened to pop up that was less of a project for me so this one is heading down the road.
The saw is in no way a pretty saw, but it is all orange or some flavor of orange.
Issues or concerns that I can remember or have seen, I have not doubt that there may be more:
Looks to have an AM cylinder that is scored.
AM recoil.
Recoil holes wallowed out.
When the recoil was installed the screws used were too long, the bottom left screw went straight into the fuel tank .
Wallowed out top cover holes.
Kill switch wire from the coil to the switch is broken.
Odd spot on the front lower AV mount(I wasn't concerned because I was going to mill with it).
Muffler dented.
You will also need top cover screws and recoil screws, I have all the muffler and mount screws.
$325 net to me powerhead only plus shipping. I can get an oem 395 cylinder kit for this saw for another 125.
Here's some more pictures.
https://photos.app.goo.gl/DrwDVMA3RG6Tt6Nw6Thanks Brett

 

[chipper1]

No takers on this big beast, I've got it in a box and ready to go.
Also have a cylinder kit sitting here for it.

 

[Logger nate]

I’ll take it if you throw cyl kit in, $350 total shipped

 

[Logger nate]

Just messing with ya buddy, looks like a good project, GLWS.

 

[chipper1]

Yeah, for sure, I know what shipping to your area costs .

 

[farmer steve]

Definitely not kitchen table material. .

 

[chipper1]

Definitely not kitchen table material. .

Got a good one don't I .

 

[PA Dan]

Still got this Brett?

 

[Mg_arborist]

Is this still available?

Sent from my SM-G960U using Tapatalk

 

[chipper1]

Still got this Brett?

Is this still available?

Sent from my SM-G960U using Tapatalk

Still available guys.

 

[Mg_arborist]

I am interested in the saw and top end. How bad are the screw holes? They all need helicoils?

Sent from my SM-G960U using Tapatalk

 

[chipper1]

I am interested in the saw and top end. How bad are the screw holes? They all need helicoils?

Sent from my SM-G960U using Tapatalk

Just realized you're a new member, welcome to AS .
That's what I would want done.
I've seen others use coarse threads screws like from the handles into the plastic or the larger one that goes into the AV on the cylinder.
@Jacob J. may be able to make some suggestions.

 

[Mg_arborist]

Cool. Thanks for the welcome, I've actually been lurking a long time, and was a member back in 2009. . . Bought a ported dolmar 7900 from jasha Reynolds. Been so long I forgot my login info lol

Sent from my SM-G960U using Tapatalk

 

[chipper1]

Cool. Thanks for the welcome, I've actually been lurking a long time, and was a member back in 2009. . . Bought a ported dolmar 7900 from jasha Reynolds. Been so long I forgot my login info lol

Sent from my SM-G960U using Tapatalk

For sure. You should be welcoming me then .
I like those ported 7900/7910's .
Did you contact a mod, @pioneerguy600 can you help him retrieve his old username/passwords?

I sent you a PM.

 

[chipper1]

Sold pending funds.

 

[Tpagel]

Nice Brett! Did your buddy Bill buy it?

 

[Mg_arborist]

Nice Brett! Did your buddy Bill buy it?

Nope, I did! Just waiting for the cash to hit my PayPal account.

Sent from my SM-G960U using Tapatalk