Cs-590/620 muffler mod

[STOVE]

I have read a lot on the site about the different ways everyone modifies the cs590/620 muffler. As well as the bold on aluminum port for the top.

Being a one piece design it doesn’t allow for a bark box style.

Has anyone added a universal style port to the side of the muffler? Is it possible with no access to add a nut ? Would be a weld up I assume or a pop rivet .

Would that addition even be worth it?

 

[NSEric]

You can just cut a fish gill in the side of the muffler in front of the seam and pry it open, no need to weld.
A lot of guys totally gut the muffler under the stock deflector, it makes them run good but is very loud as the baffles in the middle of the muffler make it act like a tiny little can with the opening back there.
IMO it's better to have an extra opening in front of the baffle plate/crimped seam on these saws instead of a big opening behind the baffle plate.
I have both on my saw, I didnt open it up too much under the deflector and it wasnt too loud or very fast so I added the fish gill and it liked that and runs better.

 

[Johnwell]

I have a 590 that I bought used that somebody gutted the muffler on. It was obscenely loud so I welded a 3/4” pipe back in the muffler and made a plate with a ~1/2” hole through it to tame it back down. Still flows better than stock, but far less obnoxious.

 

[WoodmanSr]

Has anyone added a universal style port to the side of the muffler? Is it possible with no access to add a nut ? Would be a weld up I assume or a pop rivet .

Not used then but kits from Westcoastsaw.com offer that solution. A bit pricy but nice stainless deflectors, 3 sizes choice, or hardware kit only for $7.95.

HW kit comes with a nut (piece) to crush & crimp the blind nut inserts to your muffler shell.

Search their site;

UNIVERSAL POWER PORT​

 

[STOVE]

Not used then but kits from Westcoastsaw.com offer that solution. A bit pricy but nice stainless deflectors, 3 sizes choice, or hardware kit only for $7.95.

HW kit comes with a nut (piece) to crush & crimp the blind nut inserts to your muffler shell.

Search their site;

UNIVERSAL POWER PORT​

Egan has a port as well, but I’m really wondering if adding one on the side would add any performance

 

[Chevboy0167]

The real benefit is heat reduction. More air volume through a hot tin can reduces temperature.... also pulls heat away from cylinder like a heatsink.

Cooler saw is a happy saw......

 

[STOVE]

The real benefit is heat reduction. More air volume through a hot tin can reduces temperature.... also pulls heat away from cylinder like a heatsink.

Cooler saw is a happy saw......

Is there a point of diminishing return? Watching some of the Dyno joe 026 videos he mentioned some power loss with too much air flow?

 

[RedneckChainsawRepair]

If you got 30mins this is totally free.

Pull that inner and cut off top part to use as a metal gasket for the top deflector if want to. Hole behind tube all that is needed or go in and remove the whole tube and open right there.

Be sure to pull stops to retune carb and enjoy better running saw.

 

[Marley5]

Is there a point of diminishing return? Watching some of the Dyno joe 026 videos he mentioned some power loss with too much air flow?

I believe so.
I never mess with the port side and only open up the exhaust 80% of the port.
Like mentioned you'll have to remove the limiters and Re-tune saw.
Once this is accomplished, you'll have a much better running saw.

 

[STOVE]

I believe so.
I never mess with the port side and only open up the exhaust 80% of the port.
Like mentioned you'll have to remove the limiters and Re-tune saw.
Once this is accomplished, you'll have a much better running saw.

I am buying it used from a member here. He has done some muffler work to it already. I will certainly tune as hen says it has not been done yet.

I have only seen one photo in all my googling and forum searches with a side port added