i got a 441 mtronic that randy did.........it's angry..
i'm not to far from you.
Dyno tested....Mastermind's ported 261cm vs Stock 261cm Gotta see this one.
- Thread starter chadihman
- Start date
Help Support Arborist Forum:
i'm not to far from you.
Mike from Maine
Read that the ms362 is awesome!!!
Any chance of a run with the dual port muffler on the otherwise stock 261?
glock37
Addicted to ArboristSite
I can attest too jons 325 sq ground they out cut reg ground by far and sharp as hell I got a cut that bleed like a stuck pig for 1/2 hr
glock37
Addicted to ArboristSite
I d love to see chadiman run a stock 064 to my Masterminded 064 and see the difference ?
wink wink
wink wink
Mastermind
Work Saw Specialist
I have a feeling Chad is gonna get sick of that dyno. 
glock37
Addicted to ArboristSite
Randy wait tell you get one !
Mastermind
Work Saw Specialist
I think Chad and I have reached a deal on this one........
About the time my new shop is done.......maybe.
About the time my new shop is done.......maybe.
Dieselshawn
ArboristSite Operative
If randy has his own dyno, he would rule the build off competitions.
glock37
Addicted to ArboristSite
If randy has his own dyno, he would rule the build off competitions.
we all
hed be godstihl would hire him then !
then where would we go
I was going to say Chad you might as well spend your time building Dynos. There is no way you are going to be able to test everything that is being proposed from just this one thread. I think the whole concept is just fantastic, but there are so many scenarios that you will be run ragged. (and your wife will take the kids and leave) ; )
bryanr2
Addicted to ArboristSite
If randy has his own dyno, he would rule the build off competitions.
Doesnt he already?
He's done 23 for me now and I have NO reason to look anywhere else.
I have always run a square ground .325 on all of my 50cc saws.
bryanr2
Addicted to ArboristSite
Im running .325 on my 261cm as that is what it came with but was going to swap it over to 3/8 for simplicity among the saws. Now that it's ported I think it will handle it well. Of course Maximum bar length on a 50cc saw is going to be 18''. I usually run 16 but I have a 16 on the 241cm.
Im running .325 on my 261cm as that is what it came with but was going to swap it over to 3/8 for simplicity among the saws. Now that it's ported I think it will handle it well. Of course Maximum bar length on a 50cc saw is going to be 18''. I usually run 16 but I have a 16 on the 241cm.I don't have big wood. Did I just say that ???
Seriously, I don't like a nose heavy saw, so I have my ported 261 set up with 3/8 X 18 ES bar. Balances just right. Now, if I Had big wood.... Well, that's a different story.
Mastermind
Work Saw Specialist
Steven, all of your saws are done........I do need to put some fuel thru them now before I call em good though.
Road trip!
bryanr2
Addicted to ArboristSite
bryanr2
Addicted to ArboristSite
My heart cath got postponed til this coming Wed so I will come up following that. I did receive my new 262xp from Clint Cgrahm1 and "my oh my" pictures dont do this saw justice. The absolute "crown jewel" of my collection now. I cannot believe the condition this saw is in- Hell the 241cm, 261cm, 2153, 2171, 2188, 395 and 3120 are all brand new and they dont look as "Minty" as this saw. (I havent even bought a bar or fueled the 3120xp)
bryanr2
Addicted to ArboristSite
Here's how I roll Duane: Some of these combos aint perfect as that is what came with the saw and I havent taken the time to change them. But I believe once "ported" that the perfect ratio is 3cc to 1'' of bar. They can all do more than that but I dont have a shortage of choices.
241cm- 16''
2153- 16" 3/8 (and this particular saw is the king of the 50cc saw shootout)
261cm- 18'' .325
254xp- 18''
262xp- 18-20''
272xp- 18''
2171- 20''
064- 24"
288xp- 24''
2188- 24''
395xp- 20'' 28' 32'' (currently sporting a 20'' Sugi
3120xp- probably go for a 42 Cannon (this saw will be strictly for milling)
