ehp 2159c

[woodfarmer]

did ehp ever wake this saw up, woods port muffler mod.it used to take 7-8 pulls to get it started, yesterday 8 degs. 2 pulls, no more overheating and tons of power in the cut. it should wake-up even more after ten tanks are run through, fixed the cat for good.:biggrinbounce2:

 

[Big Daddy]

Hello Woodfarmer
Did you do them mods, if so, just how?
God Bless
Big Daddy

 

[John Ellison]

Good looking saw. Looks like a bolt is loose in the starter cover.

 

[Hired Gun]

Congrats on the Red 359 lol You are going to love it!!! :hmm3grin2orange:

 

[woodfarmer]

i had someone do the modding, i did tighten up the screws after the pics were taken and then rocked on some 12" beech

 

[B_Turner]

did ehp ever wake this saw up, woods port muffler mod.it used to take 7-8 pulls to get it started, yesterday 8 degs. 2 pulls, no more overheating and tons of power in the cut. it should wake-up even more after ten tanks are run through, fixed the cat for good.:biggrinbounce2:

How much louder is it?

Just wondering, not trying to start something.

 

[woodfarmer]

noticeable, its sounds slightly louder than a stock 2171, but i always wear my ear muffs so it doesn't bother me at all, its one sweeeet sound.

 

[MAG58]

Really Good Looking Saw. I wonder if it's louder then the original 2159 Tube Muffler over here?

 

[SWE#Kipp]

Really Good Looking Saw. I wonder if it's louder then the original 2159 Tube Muffler over here?


If you wonder about the modded muffler the answer is yes I modded a DF muffler for my 357xpg it had a tube originally that I kept for times when I maybe would like a quiet saw

 

[MAG58]

Really Good Looking Saw. I wonder if it's louder then the original 2159 Tube Muffler over here?


If you wonder about the modded muffler the answer is yes I modded a DF muffler for my 357xpg it had a tube originally that I kept for times when I maybe would like a quiet saw

OK, more noise but did you gain anything power-vise

 

[SWE#Kipp]

yes, you gain quite a bit
you should try it !!!
It's the cheapest performance gain you can get ,,,

 

[MAG58]

yes, you gain quite a bit
you should try it !!!
It's the cheapest performance gain you can get ,,,

Well, I have to get me one DF muffler to do the modding on, and keep my Tube muffler for more quiet times But I have to wait to the saw is broken in

 

[Urbicide]

yes, you gain quite a bit
you should try it !!!
It's the cheapest performance gain you can get ,,,

Hello SWE#Kipp. I was wondering what size tube you used in your muffler mod. Did your muffler have an internal baffle plate and if so how did you modify it?

Take care.

Vince

 

[MAG58]

The Top port DF muffler I have seen is empty inside, like mine Jred 2152

 

[SawTroll]

The latest reports from EHP says that his latest 361s beats his best 359/357xps by some margin.......:hmm3grin2orange: :hmm3grin2orange:

 

[BostonBull]

The latest reports from EHP says that his latest 361s beats his best 359/357xps by some margin.......:hmm3grin2orange: :hmm3grin2orange:

Thats because Stihls are better! :hmm3grin2orange:

 

[SawTroll]

Thats because Stihls are better! :hmm3grin2orange:

Not generally, but the 361 is..........

 

[Urbicide]

The Top port DF muffler I have seen is empty inside, like mine Jred 2152

I have a 357XP/359 muffler with the part # 503 91 75-03 L. It is a non-cat muffler. It has a baffle plate located inside at the junction where the front and rear muffler halves are brazed together. The baffle has a single opening in it located at the lower right hand corner as viewed through the inlet. I would estimate the opening to be pretty close to 20 mm in diameter. The exhaust port is located on the top of the muffler in the back. Why the engineers put it there is beyond me. It makes for a crispy-edged top cover.opcorn:

 

[rahtreelimbs]

Having both EHP359's & EHP361's I can tell you that both are really tremendous saws!!!

Torque is about even............the difference is that the 361 pulls about 1'000 RPM higher.

But you are payimg for that since the 361 is more $$$ than the 359!!!

 

[SawTroll]

Having both EHP359's & EHP361's I can tell you that both are really tremendous saws!!!

Torque is about even............the difference is that the 361 pulls about 1'000 RPM higher.

But you are payimg for that since the 361 is more $$$ than the 359!!!

I believe Ed has developed his 361s more than his 359s after that.......:biggrinbounce2: :biggrinbounce2: