Iowa Fall 2012 GTG

[srcarr52]

For some reason the bore in the jug on the left looks to be bigger than 44mm... Very interesting!!

That is because it's a 45mm kit. Duh!

 

[ancy]

Well I will be out for the next 10 days chasing these....

Sounds like it was taken about a mile from camp. Man I had some bad luck this week with the bow shop breaking my bow to me trying to get a new one set up. With all the chitty luck I should end up with a 400" bull and 5 naked tree hugers to haul it out!! Talk to you when I get back.

View attachment 250816

 

[Homelite410]

That is because it's a 45mm kit. Duh!

Ya..... Looks like 47 to me!!

 

[Ronaldo]

Well I will be out for the next 10 days chasing these....

Sounds like it was taken about a mile from camp. Man I had some bad luck this week with the bow shop breaking my bow to me trying to get a new one set up. With all the chitty luck I should end up with a 400" bull and 5 naked tree hugers to haul it out!! Talk to you when I get back.

View attachment 250816

Good luck to ya on the hunt Ancy-----shoot straight!

Ron

 

[moody]

Need some assistance gentlemen. Could someone identify the 346 quad port am cylinder for me?

Thanks in advance.

they all appear to be 346's the two on the left seem to be the NE version which is 44 mm the old is 42.

 

[moody]

So hopefully I'll be done with my hot saw project by then. I've got a couple stone age saws i'll have to bring my Great Grandfathers Mono being one of them. I guess the real question is who's ready to make some cookies?

 

[Hedgerow]

So hopefully I'll be done with my hot saw project by then. I've got a couple stone age saws i'll have to bring my Great Grandfathers Mono being one of them. I guess the real question is who's ready to make some cookies?

Still haven't touched the 350...:msp_thumbdn:

Looked at it yesterday though...:msp_smile:

 

[mweba]

Has no one in this thread seen a 346 jug?

 

[moody]

Still haven't touched the 350...:msp_thumbdn:

Looked at it yesterday though...:msp_smile:

mine may end up a 350.......CC. That's good new's looking is always a good start.

 

[Hedgerow]

Has no one in this thread seen a 346 jug?

I've seen lots of them, but never whittled on any...

 

[8433jeff]

Subscribed.

 

[Stumpys Customs]

Need some assistance gentlemen. Could someone identify the 346 quad port am cylinder for me?

Thanks in advance.

The two on the left look like the 45mm 350/353 cyl's. The two on the right look like the early 44mm 350cyl. None of those are 346 cyl. The 346 OE will measure 42mm & the NE is 44.3mm.

Here's a pic of the inside of a NE 44.3mm 346 cylinder.

This shows the difference int he way the outside of the transfers look

Here's an aftermarket 44.3mm 346 cyl. looks pretty much the same.

 

[mweba]

Bingo Stumpy. They sent me four cylinders trying to get it right. Would you pm me the seller that has that am cylinder? Although I believe it will be the same one I dealt with.

 

[heimannm]

Mitch - I looked again and see that Wendel sent me home with a repro diaphragm and gasket, waiting for you any time...I will be busy cutting tomorrow but you are welcome to visit the shop. Look for a blue wrap on the router table.

Mark

 

[Homelite410]

This shows the difference int he way the outside of the transfers look

Stumpy,

I need 4 of these clamps!! Where did you get them?

 

[Stumpys Customs]

This shows the difference int he way the outside of the transfers look

Stumpy,

I need 4 of these clamps!! Where did you get them?

I think they are 372xp clamps. I'm out of them right now.

 

[Homelite410]

Thanks Stump... Ill talk to my local dealer n see what i come up with!

 

[hoskvarna]

milling with 2188

this is what ronaldo and i did saturday.cut 6 slabs,30"wide x4"thick x 6' plus long.32" dry ash ,hard cut! maiden voyage for mill and saw.

 

[hoskvarna]

More Pics

6636624[/IMG]

 

[hoskvarna]

More Pics