Oklahoma,AR,MO,KS,TX GTG (Next GTG 08/27/2016 ) Fort Scott, KS

[sunfish]

Don (@sunfish ) - you bought the Maxx from Bailey's last month, right? Review?

After using it a a few times, I'd buy the Maxx again. It grinds both sides the same without reversing the motor. High quality and very easy to use. The auto clamp is the chit!

 

[Homelite410]

So we watched mad max fury road last night..... There is 2 hours of my life that I'll never get back... No plot, stupid story, bad ass vehicles that are very unpractical............ And Max isn't the main character. Smh....

 

[lumberjackchef]

Morning fellas! We arrived at Dawt Mill down by Tecumseh, mo. last night about midnight. Gonna be set up for their craft fair to carve all weekend. It's really pretty down here on the North fork river!

Sent from my MotoE2(4G-LTE) using Tapatalk

 

[workshop]

Looking for opinions.
If you were looking at brand new saws, 80-90cc + or -, what would you get? And why. Stock saw.
Let the debates begin.

 

[Hedgerow]

7910 without hesitation.

 

[sunfish]

Looking for opinions.
If you were looking at brand new saws, 80-90cc + or -, what would you get? And why. Stock saw.
Let the debates begin.

I'd want a Husky 390xp or a Dolmar 7910. Just because.

 

[WKEND LUMBERJAK]

Matt and Don have said it all. Well Steve this discussion is over.that was quick and easy. 7900/7910 would be my choice 390 I have no time on.

 

[Hedgerow]

Steve even has a dealer right there in his hometown.
No brainer..
Lol..

 

[67L36Driver]

What little experience I have with Dolmars, I have to agree with the above.
A Dolmar is everything a Stihl or Husqvarna wants to be.

But, dealer service and parts availability?

 

[67L36Driver]

Darn if this thing runs and cuts. I wouldn't have bet on it.[emoji849]

 

[workshop]

Nixa hardware is a Dolmar dealer, but the only thing on the shelf is a 510. And it's been there for 3 years. They're a huge Stihl dealer. Haralds small engine is a dealer and keeps stuff im stock too. Open m-f till 6. Closed weekends. Is Dolmar in bound clutch or out bound clutch?

 

[awol]

Looking for opinions.
If you were looking at brand new saws, 80-90cc + or -, what would you get? And why. Stock saw.
Let the debates begin.

390xp, cause I got a new one and will make you a good deal on it! 7910s are great saws though, and at a little lower cost I think.

 

[workshop]

Dolmar says it will pull a 32 inch bar.

 

[concretegrazer]

7910, 461, 390xp, 576xp. All good runners. Get the one that's the best deal.

Is Dolmar in bound clutch or out bound clutch?

Inboard.

 

[cobey]

Got one side back together last night
I have to pick up bearings in a bit to finish this one.

Chipping away at this thing....

 

[Hinerman]

7910 without hesitation.

I'd want a Husky 390xp or a Dolmar 7910. Just because.

Solo 681 anybody? No love for the 661 either. How about the Echo 8000

 

[concretegrazer]

Solo 681 anybody? No love for the 661 either. How about the Echo 8000

Show me where can you get a new 681? Sure if your buying. You had to go there....

 

[67L36Driver]

Husky 345 worth much?

 

[WKEND LUMBERJAK]

Husky 345 worth much?

nice little runners trim limiters on carb and a muffler mod.

 

[Homelite410]

Husky 345 worth much?

They are awesome when you put a 346 p&c on it..