Oklahoma,AR,MO,KS,TX GTG (Next GTG 08/27/2016 ) Fort Scott, KS

[67L36Driver]

Renewed my C'list add and already have three scammers bouncing offers to have their 'agent to pick up the item'.
They earned a GFY for their time.

Two more. Bastards are hip deep this morning![emoji35]

 

[Hedgerow]

Good Morning! Quick question has anyone had any luck with hyway cylinders, I know they are cheap but didn't know if you clean them up if they would be usable or just shelf art?

They are serviceable..
Cheap way to get one back in the game.

 

[workshop]

Afternoon everybody.

 

[WKEND LUMBERJAK]

Sun is starting to peek out.

 

[67L36Driver]

Husqvarna 50 hit the porch. Saw & case in huge Toro 'Power Shovel' box. Fuel and oil still on board! Yikes!

Got it to run and adjusted carb without the air filter. But, when I put AF in place, loads up and floods out. The plastic has taken a permanent set because the saw was stored with the choke slide up.

 

[67L36Driver]

With a squirt of WD-40, pumps 170.[emoji848]
Pumps 160 after cutting a cookie.

Real puzzle is, the air filter is squeaky clean but chokes down the saw. Runs great without it.[emoji849]

Plenty of room at the choke bump.[emoji57]

 

[WKEND LUMBERJAK]

With a squirt of WD-40, pumps 170.[emoji848]
Pumps 160 after cutting a cookie.

Real puzzle is, the air filter is squeaky clean but chokes down the saw. Runs great without it.[emoji849]

Plenty of room at the choke bump.[emoji57]

post up a picture.

 

[WKEND LUMBERJAK]

Good evening from Parsons Ks.

 

[ARsawMechanic]

You might check into your Metering diaphragm, lever, & needle. Especially if it had old gas in it.

Sent from my SM-G920V using Tapatalk

 

[ARsawMechanic]

I was coming out of a restraunt in Bentonville last week, & happened to glance up at the road in time to witness a white dodge pickup pulling a trailer with "R Value" written on the sides. . Anybody here know that guy?

Sent from my SM-G920V using Tapatalk

 

[workshop]

That's Dan.

 

[lumberjackchef]

With a squirt of WD-40, pumps 170.[emoji848]
Pumps 160 after cutting a cookie.

Real puzzle is, the air filter is squeaky clean but chokes down the saw. Runs great without it.[emoji849]

Plenty of room at the choke bump.[emoji57]

Is it the flocked one or the fine nylon mesh? I had a homie 50 doing that tonight and it had the fine mesh type that didn't appear that dirty until I hit it with the carb cleaner. I bet it was only pulling half of the air it should have. Runs perfect now

Sent from my MotoE2(4G-LTE) using Tapatalk

 

[Homelite410]

Alan and a comment at the charity cut at Doug's....

 

[67L36Driver]

Is it the flocked one or the fine nylon mesh? I had a homie 50 doing that tonight and it had the fine mesh type that didn't appear that dirty until I hit it with the carb cleaner. I bet it was only pulling half of the air it should have. Runs perfect now

Sent from my MotoE2(4G-LTE) using Tapatalk

Fine nylon mesh. It looked clean but I scrubbed it with Simple Green and a tooth brush anyway.
Try it out tomorrow morning.

 

[Locust Cutter]

Alan and a comment at the charity cut at Doug's....

Back when Men were Men and sheep were scared...

 

[67L36Driver]

Tomorrow is shot for saw tinkering. We are moving Michael up from NKC.
He/we can't afford the rent since he lost his job at Delta.

 

[cobey]

Tomorrow is shot for saw tinkering. We are moving Michael up from NKC.
He/we can't afford the rent since he lost his job at Delta.

Bad deal

 

[Locust Cutter]

Damn Carl...

 

[lumberjackchef]

Morning all you saw tweakers! had to get up and light the rocket stove -pellet insert I just got done fabricating the other day. Man those pellets burn steady and hot in this thing......need to find a way to make me a press to recycle some negative material from my carvings (sawdust) them little bugars are expensive if ya burned em all day! ouch! Thats whats cool about these rocket stoves is that you can burn literally any type of biomass in them that you can scrounge up. makes quick work of my negative chunks from carvings and cookies busted into pieces so they fit in the feed tube.I smell the coffeeoff to carve some more Christmas presents. Its Carve or Starve for me boys!

 

[lumberjackchef]

Oh and before I forget....Welcome to the club Sparky! What town did you sasy that you lived in BTW? I live a few miles South of Fort Scott. Cobey and I are practically neighbors. A stone throw from the Missouri Line I am! Never met a saw I didnt like for one reason or another. Collect them all for parts! The ones that start are the ones that I run.... I do chainsaw carvings, rustic log furniture, build small cabins/playhouses/treehouses etc, have a small bandsaw mill and a staionary rail mil powered by a ported 066 that i use primarily for slabbing and beam making. Oh yeah and work on small engines in my spare time including lots of saws... Nice to meet ya!