Oklahoma,AR,MO,KS,TX GTG (Next GTG 08/27/2016 ) Fort Scott, KS

[RVALUE]

Next year, mark'll send it to stumpidity...

What?

 

[Hedgerow]

What?

I saw you grinning while you were running the 2101...
You ain't fooling' me Dan...:msp_sneaky:

 

[RVALUE]

I saw you grinning while you were running the 2101...
You ain't fooling' me Dan...:msp_sneaky:

Since most of my saws don't run, ........ any runner is a grinner.

 

[Hedgerow]

Since most of my saws don't run, ........ any runner is a grinner.

If I recall, you got a decent running 757 now too...
Not bad for parts in a field on a RR tie table eh???
Probably couldn't do that again in 10 try's...
I was thankful it ran at all...:msp_biggrin:

 

[CMNRallye79]

Me too, you have no idea. When it started I was beyond thankful.

 

[Hedgerow]

Me too, you have no idea. When it started I was beyond thankful.

Proof positive a jug that bad is still serviceable!!!
Keep it fat for a few tanks...
Check it every time you start it...

 

[RVALUE]

If the factory set the high too lean, then it fits with my bad luck.

Remember it had no high set screw. We're not smart enough to set it on a professional saw.


I'm going back to wild things.

 

[Work Saw Collector]

Proof positive a jug that bad is still serviceable!!!
Keep it fat for a few tanks...
Check it every time you start it...

Have you done the acid clean up on a jug? I done a 044 the jug looked bad but a little heat in the jug a little acid and a bunch of Q tips a bunch of rubbing and that jug looked great.

Edit: I sat the jug on top of the wood stove for a while to heat it.

 

[Hedgerow]

Have you done the acid clean up on a jug? I done a 044 the jug looked bad but a little heat in the jug a little acid and a bunch of Q tips a bunch of rubbing and that jug looked great.

Did it best I could while standing in Dan's field... Got most of it out, and the rings took care of the rest...:msp_sneaky:

 

[Hedgerow]

If the factory set the high too lean, then it fits with my bad luck.

Remember it had no high set screw. We're not smart enough to set it on a professional saw.


I'm going back to wild things.

The set plugs have been removed... You can adjust all ya' want now!!!

 

[Work Saw Collector]

Did it best I could while standing in Dan's field... Got most of it out, and the rings took care of the rest...:msp_sneaky:

Cool I was just asking if you had tried it, it is a bunch of work but jugs can be saved.

 

[Work Saw Collector]

The set plugs have been removed... You can adjust all ya' want now!!!

Did his 441 have the locks, I never looked?

 

[Hedgerow]

Did his 441 have the locks, I never looked?

I didn't either... I know we picked up a new drum, rim, oiler gear, and bearing for the clutch side though.
I think Treemonkey installed them... But not sure...

 

[Hedgerow]

Cool I was just asking if you had tried it, it is a bunch of work but jugs can be saved.

Yea. Mark found me some muratic acid and q-tips, and I worked it over for a bit, then might have run out of daylight, so we rolled with it...

 

[Work Saw Collector]

I didn't either... I know we picked up a new drum, rim, oiler gear, and bearing for the clutch side though.
I think Treemonkey installed them... But not sure...

Scott is a great guy to be around.

 

[Hedgerow]

Scott is a great guy to be around.

Yup... Hey, are you gonna make it to Kentucky this weekend?

 

[Work Saw Collector]

Yup... Hey, are you gonna make it to Kentucky this weekend?

I don't even know yet, I shouldn't I am behind. If I get some things done I would like to.

 

[Work Saw Collector]

Are you thinking about it?

 

[Hedgerow]

Are you thinking about it?

No... I have been travelling enough this year... It's time to get the barn filled back up... :bang:

 

[Work Saw Collector]

No... I have been travelling enough this year... It's time to get the barn filled back up... :bang:

I understand that.