Parts Husqvarna 254XP

[C@TCH]

I couldn’t start my old saw and when I removed air filter I found idle screw and spring laying in bottom. I also noticed a hole with threads on side of carb but didn’t find anything. Carb is a Walbro HDA 35B hard to find a parts diagram but think its called a throttle stop is what’s missing. It’s the hole in picture above HDA. Anyone have any idea what’s missing and where to get one.

 

[Derf]

It’s the choke lock you’re missing.

I don’t know if Walbro supports parts on these old carbs. You can cross reference the part on the HD-35 with the HD-120 and the HD-144. I think also the HD-87 has the same part. But it may just be easier to search ebay for a replacement carb if you can’t find that one piece.

 

[SteveSr]

You could also try these guys:

https://www.vepetersen.com/
They are a master Walbro distributor and have some obsolete and NOS inventory. If not, they may be able to cross it to an available part.

 

[Huskvarna hotellgäst]

It's the idle stop / part-throttle lever & screw. Part numbers at bottom right.

 

[C@TCH]

Thanks for your replies, seems hard to find this little part and screw. I will keep digging but I think it’s obsolete. I thought maybe someone on here would have parts for old saws.

 

[Derf]

Thanks for your replies, seems hard to find this little part and screw. I will keep digging but I think it’s obsolete. I thought maybe someone on here would have parts for old saws.

Parts for old saws, sure. I know some people have spare carbs for this 2-series of saws. But you’d have to buy a whole used carb off someone. Doubtful that someone has spare parts for a carb, other than a diaphragm kit. Your best bet is likely ebay, get a used carb.

 

[Modifiedmark]

You could also try these guys:

https://www.vepetersen.com/
They are a master Walbro distributor and have some obsolete and NOS inventory. If not, they may be able to cross it to an available part.

That is good advice except VE Peterson went to all UPS shipping. It would cost $15 to ship that tiny little lever.. At least thats what they told me the last time I called them a few years ago.

 

[irhunter]

I would contact Walbro cust service directly. They have helped me find parts which were NLA.

 

[Huskvarna hotellgäst]

This may not help but late-model Husky 44s also had an HDA carb with this throttle stop. 44 "Special" actually had the 254 HDA35B carb.

 

[C@TCH]

It’s the choke lock you’re missing.

I don’t know if Walbro supports parts on these old carbs. You can cross reference the part on the HD-35 with the HD-120 and the HD-144. I think also the HD-87 has the same part. But it may just be easier to search ebay for a replacement carb if you can’t find that one piece.

Thanks derf, I didnt notice you sent this. Don’t get on here much. I received parts and put it on.

That is good advice except VE Peterson went to all UPS shipping. It would cost $15 to ship that tiny little lever.. At least thats what they told me the last time I called them a few years ago.

Ended up getting one from Repairclinic.
https://www.repairclinic.com/PartDetail/Throttle-Control-Lever/68-19-7/2699237

That is good advice except VE Peterson went to all UPS shipping. It would cost $15 to ship that tiny little lever.. At least thats what they told me the last time I called them a few years ago.

I couldn’t start my old saw and when I removed air filter I found idle screw and spring laying in bottom. I also noticed a hole with threads on side of carb but didn’t find anything. Carb is a Walbro HDA 35B hard to find a parts diagram but think its called a throttle stop is what’s missing. It’s the hole in picture above HDA. Anyone have any idea what’s missing and where to get one.View attachment 860500

Got one from here. https://www.repairclinic.com/PartDetail/Throttle-Control-Lever/68-19-7/2699237