Pioneer 620 - bringing it back to life

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

cdahl383

ArboristSite Lurker
Joined
Nov 14, 2024
Messages
28
Reaction score
32
Location
Michigan
Recently picked up an old Pioneer 620 chainsaw. The seller said it was his father-in-law's (the seller looked to be in his late 60's to early 70's). He wasn't sure if his father-in-law bought it new or not, but said he had it for a very long time. It looked like it sat in the corner of the garage for decades. Very dusty/dirty, but appeared to be complete. I brought some tools and my compression gauge with me when I checked it out. It had good compression and looked complete, so I bought it.

I brought it home and spent some time just cleaning it up. Not a fan of working on dirty stuff. Got it cleaned up pretty good and then did some basic diagnostics on it. Checked the compression (showed 150psi on my gauge), verified that it had spark, and took the muffler off to check out the piston/cylinder through the exhaust port (looked really good). Everything seemed to look pretty good. I opened the fuel tank and it was all varnished up in there and stunk terrible. I pulled the sediment bowl/fuel line out and filled the tank with Berryman Chem-Dip carb cleaner. Four hours later the tank was spotless!

I ordered a carb rebuild kit for the old Tillotson HL22A carb, cleaned the existing air filter, and continued cleaning the saw up as much as I could. Now I'm just waiting for the carb rebuild kit and a few other small things. Hoping after rebuilding the carb I can get it fired up and running again! No plans to put it into serious use, but would like to use it occasionally around the house to cut up a little firewood just for fun.

Here's a few photos / videos I've taken along the way so far:





 

Attachments

  • thumbnail_IMG_2301.jpg
    thumbnail_IMG_2301.jpg
    715.2 KB
  • thumbnail_IMG_2302.jpg
    thumbnail_IMG_2302.jpg
    823.7 KB
  • thumbnail_IMG_2304.jpg
    thumbnail_IMG_2304.jpg
    766.7 KB
  • thumbnail_IMG_2306.jpg
    thumbnail_IMG_2306.jpg
    938.3 KB
  • thumbnail_IMG_2308.jpg
    thumbnail_IMG_2308.jpg
    760.1 KB
Here's some photos after I cleaned it up a little bit and a couple before/after photos of the fuel tank...
 

Attachments

  • thumbnail_IMG_2420 (1).jpg
    thumbnail_IMG_2420 (1).jpg
    365.9 KB
  • thumbnail_IMG_2454 (1).jpg
    thumbnail_IMG_2454 (1).jpg
    366.9 KB
  • thumbnail_IMG_2431 (1).jpg
    thumbnail_IMG_2431 (1).jpg
    821.3 KB
  • thumbnail_IMG_2397.jpg
    thumbnail_IMG_2397.jpg
    677.7 KB
  • thumbnail_IMG_2394.jpg
    thumbnail_IMG_2394.jpg
    791.1 KB
  • thumbnail_IMG_2392.jpg
    thumbnail_IMG_2392.jpg
    785.2 KB
  • thumbnail_IMG_2334.jpg
    thumbnail_IMG_2334.jpg
    604.4 KB
  • thumbnail_IMG_2333.jpg
    thumbnail_IMG_2333.jpg
    582.7 KB
Cleaned and rebuilt the carb last weekend. Got it to fire up and run, but it didn't run very well. Smoked a lot and wouldn't rev up or idle. Appeared to be running very rich.

I suspected an issue with the carb, particularly the needle/metering lever as the kit I bought had significantly differently looking metering lever and needle. I took the carb back off and swapped the original needle and metering lever back in. I also noticed the metering lever was not flush with the chamber floor, so I adjusted that as well. Hoping that does the trick.

I haven't had a chance to fire it back up since it was snowing out and we got busy around Thanksgiving. Hoping it runs good now, we'll see.

Also replaced the fuel line and filter as it had the original line and filter on it when I pulled the sediment bowl out. It had a little small felt filter in the sediment bowl. Not sure where to get one of those, so I just cleaned that one really good using dirtbike air filter cleaner and Chem dip. It came out pretty good and seems to be fine as the saw is pulling fuel from the tank through the bowl, etc.

I also tested out the oiler. I dumped some bar oil into the bar oil tank and pushed the lever about a dozen times or so. It finally picked up some oil and started squirting it out of the oil port by the bar mount. Excellent! At least I know that works now.
 

Attachments

  • thumbnail_IMG_2669.jpg
    thumbnail_IMG_2669.jpg
    577.1 KB
  • thumbnail_IMG_2671.jpg
    thumbnail_IMG_2671.jpg
    756.6 KB
  • thumbnail_IMG_2673.jpg
    thumbnail_IMG_2673.jpg
    1.1 MB
  • thumbnail_IMG_2682.jpg
    thumbnail_IMG_2682.jpg
    311.9 KB
That looks like the original style needle and lever, without a fork. Any modern kit will have a forked lever needle, make sure they are engaged. Make sure the lever pivots freely in the carb body, some aftermarket kits give issues here. A little filing to the side of the lever will fix this. Replace the oring on the high speed needle, should take a 007. This can cause an slight air leak. Doesn't look like your low speed has any spring or seal there. In an extreme case, the welch plug in the fuel chamber can leak fuel causing a rich condition.

Hopefully those carb parts pictured are the old ones and not what you are trying to use.

Finally, make sure the choke is open. I had trouble once tuning a saw, turns out the choke was closed. Operator error.
 
That looks like the original style needle and lever, without a fork. Any modern kit will have a forked lever needle, make sure they are engaged. Make sure the lever pivots freely in the carb body, some aftermarket kits give issues here. A little filing to the side of the lever will fix this. Replace the oring on the high speed needle, should take a 007. This can cause an slight air leak. Doesn't look like your low speed has any spring or seal there. In an extreme case, the welch plug in the fuel chamber can leak fuel causing a rich condition.

Hopefully those carb parts pictured are the old ones and not what you are trying to use.

Finally, make sure the choke is open. I had trouble once tuning a saw, turns out the choke was closed. Operator error.
The kit came with o rings. I’ll have to replace them. Wasn’t sure what those were for at first.

I didn’t replace the Welch plug. Maybe something is dirty below that? I don’t fully understand what the function of the Welch plug even is honestly. Still learning.

Yes, those are the old parts. I just laid them out so I would remember the order of everything.

I made sure the choke was open. It sort of springs back when you open it. That’s how I remembered if it was open or closed since there is no indicator anywhere.

If it’s still running goofy I’ll pull it off again and look at the Welch plug. I can replace the o rings on the needles with the carb on the saw.
 
The welch plug covers metering ports into the throat. Without it, fuel would run straight into the motor without being adjusted by the needle. Don't try to run aggressive tools through the ports if they are dirty. Carb cleaner has always been the only thing necessary. I'm sure there are videos on YouTube if you decide to remove the plug. Be careful here. If the chamber was clean when you pulled the diaphragm odds are it's clean under the plug.

FYI, raising the lever relative to the floor would tend to make it rich, lowering it leaner.

A Mityvac is a useful tool for checking leaking needles and seats.
 
The kit came with o rings. I’ll have to replace them. Wasn’t sure what those were for at first.

I didn’t replace the Welch plug. Maybe something is dirty below that? I don’t fully understand what the function of the Welch plug even is honestly. Still learning.

Yes, those are the old parts. I just laid them out so I would remember the order of everything.

I made sure the choke was open. It sort of springs back when you open it. That’s how I remembered if it was open or closed since there is no indicator anywhere.

If it’s still running goofy I’ll pull it off again and look at the Welch plug. I can replace the o rings on the needles with the carb on the saw.
Acquired a 600 under similar means & condition. Sat 45 years or longer in dad's basement.
Those are interesting fuel pickup. Pic of my rebuild.

Do you have a Tach. Remember those old girls only turn 5500 rpm WOT. Mine sounds horribly rich there. Not more than 10 minutes in wood. It will wear you out & wanting for a modern saw. Just have as nostalgia (would sell probably).

Shown with another oldie, Sears 758G (David Bradley).
 

Attachments

  • 20221209_154349.jpg
    20221209_154349.jpg
    1.9 MB
  • 20221209_154022.jpg
    20221209_154022.jpg
    1.2 MB
  • 20221213_151654.jpg
    20221213_151654.jpg
    3 MB
The welch plug covers metering ports into the throat. Without it, fuel would run straight into the motor without being adjusted by the needle. Don't try to run aggressive tools through the ports if they are dirty. Carb cleaner has always been the only thing necessary. I'm sure there are videos on YouTube if you decide to remove the plug. Be careful here. If the chamber was clean when you pulled the diaphragm odds are it's clean under the plug.

FYI, raising the lever relative to the floor would tend to make it rich, lowering it leaner.

A Mityvac is a useful tool for checking leaking needles and seats.
Ok cool. The insides of the carb were pretty clean when I pulled it apart. I think I’ll leave that alone for now.

I soaked the metal carb body in chem dip for a couple hours then cleaned and sprayed all passages with carb cleaner. Appeared to be very clean afterwards.

Yes I think the lever was too high before. That may have been causing the rich condition. I’ll have to test it out again and see how it runs.

I just recently got a mityvac. If I end up taking the carb off again I’ll test it. I did see some YouTube videos out there about how to do that, as well as test the crank seals for air leaks.
 
You can test needle and seat thru the fuel line without removing the carb. Should hold pressure up around 12-15 pounds I think and release. You'll at least learn if the needle wants to leak or not.
I may try that next time I have the carb off. The way the fuel line is situated on this saw it really sucks to get it off. I have to loosen the sediment bowl too as the fuel line is literally only an inch or so long from the sediment bowl to carb.
 

Latest posts

Back
Top