Want to Buy ported 90cc

[SAWMIKAZE]

Im huntin somethin in the 90cc range thats in good enough shape from a reputible builder lemme know what you got

 

[shorthunter]

I just listed a dolmar 133 if you have any interest in older saws or sachs-dolmar saws. It does not have any port work, appears to be a virgin saw which hasent been taken apart

 

[o8f150]

I have a sweet solo 603,,, it has only had 8 tanks run through it,, it is dang near mint,,, would take 600 PHO

 

[bryanr2]

Scott,
Still cant figure why you're letting that beauty go. A saw like that, in that condition, is next to unreplaceable. I havent used my Sachs Dolmar in over a year. It's been drained and put up. I cant bring myself to sell it though.

 

[mdavlee]

That 603 is good looking. Too bad the dealer support for arts is non existent. They seem to run strong. I've got a ugly 288 I just put together. Probably be up for sale when I get the last parts for it.

 

[o8f150]

Scott,
Still cant figure why you're letting that beauty go. A saw like that, in that condition, is next to unreplaceable. I havent used my Sachs Dolmar in over a year. It's been drained and put up. I cant bring myself to sell it though.

i use it maybe once or twice a year,, be nice to see it used more often then what it is,, its not that i have to sell it,, if it never sells then it will be used once in a while,,,here is the vid where uncle was running it last year with a 36" b/c on it

 

[nmurph]

Scott, is that saw ported? I almost pulled the trigger on it a few weeks ago.

 

[bryanr2]

nope- he never sentt it to the monkey

 

[o8f150]

Scott, is that saw ported? I almost pulled the trigger on it a few weeks ago.

nope,, its been MM'd and the base gasket taken out,, squish is .024 now,, have no idea what the comp is,, it hurts to bad pulling it without the decomp

 

[nmurph]

Port it and I will give you $600 for it (shipped, of course).

 

[o8f150]

Port it and I will give you $600 for it (shipped, of course).

wake up neal,,,, and stop smoking bat crap

 

[fin460]

I have a 066 non decomp squish cut and transfers ported by Mastermind, Preston Teague ported the intake and exhaust. I bought it from Preston it is an awesome running saw. $875 shipped with a 34" Oregon lightweight bar and chain, or 775 PHO

 

[fin460]

I'm having trouble uploading photos, I assume because the site says it is having trouble.

 

[bryanr2]

that 603 seems pretty beasty as it is.

 

[o8f150]

that 603 seems pretty beasty as it is.

that it is,,, when I was running the 24" b/c in the 1st vid I was pulling real hard on it,,, its 103cc's of raw screaming madness

 

[nmurph]

wake up neal,,,, and stop smoking bat crap

It's guano man, Labrador and guano...good stuff.........

 

[SAWMIKAZE]

Appreciate the offer scott just not really into the solos..lookin for stihl/jonsered/husky..

 

[fin460]

Sent from my iPhone using Tapatalk

 

[fin460]

I cut up a big 40" oak with it today, It runs strong with that 34" bar buried and full comp

 

[srcarr52]

I'll have a 394 fresh off the porting bench probably by the end of next week. Fresh piston, seals, and bearings ect. I was just building it to sell it anyway, $650 as a low top PHO.