Post your 2 series Husky thread

[rattler362]

Hey I got alot of friends from laurel.

Sent from my XT1060 using Tapatalk

 

[weimedog]

Pictures yes!

Some pics...built from "junk" have a video up over on the YouTube channel. Has new bearings and seals. Popup piston. Cut cylinder base to get .020" squish with a OEM base gasket. Covered up the stock muffler outlet and brazed in a 5/8 dia x 1.5 in long tube....a true Chits & grins saw. And it runs quite well...

 

[Perry pioneer]

I like it, what's the psi on that? And did you do any porting on it? 2xx series are so fun to work on and build, good job... Perry

 

[Perry pioneer]

Oh and I like that pop up too!

 

[weimedog]

Right now its a little more than 180 - maybe 185. I don't trust my gage. I left the ports alone but since the cylinder is lower by .020 it has a little more intake duration and the exhaust opens a little later. Runs best when set at 13300-13500 right now so it predictably didn't pick up RPM's but pulls quite a bit harder than the stock one I had for a reference.

 

[rattler362]

Right now its a little more than 180 - maybe 185. I don't trust my gage. I left the ports alone but since the cylinder is lower by .020 it has a little more intake duration and the exhaust opens a little later. Runs best when set at 13300-13500 right now so it predictably didn't pick up RPM's but pulls quite a bit harder than the stock one I had for a reference.

Mine blows 180# with new ring

Sent from my XT1060 using Tapatalk

 

[volvo2før]

Two buddies in Norwegian forest! 242xpg and 254g

 

[motor head]

MY 281

 

[cus_deluxe]

 

[Drptrch]

2100 & 281

Oops, wrong 2-series [emoji13][emoji13]

 

[motor head]

Here's my 266

 

[SS Sniper]

View attachment 549282

That's a sweet looking saw! Very nice

 

[chipper1]

Project.
Piston is clean .

 

[r black]

clean 262

 

[Big_6]

My (2) discontinued
235x-torq. lp. brush cutters gone to new homes.

One saw had tool-less bar & chain adjustment!
I put the proper L/H tune on these and got into some 20" maple!

 

[chipper1]

clean 262

That's it lol.

 

[Cantdog]

Well......this isn't my saw, but one I built a while back for a logger friend. He had worn out four 262 XP from brand new and was whining that he couldn't buy any more. I took his four saws and salvaged what I could of the best parts from each. He really wears a saw out......when it's done, it's done so I also needed a lot of new parts but he was more than happy to pony up the cash. This is ported as far as I dared go with it and the squish set at 0.020....one of the great salvages was from his first 262....a 1990 model...the #87 Walbro.....awesome carb....to bad they only used it two years on these saws....really breaths and work well with the porting and the Walker or Walker clone muffler. Brutus little saw with a 16" bar in 0.058 X 3/8" full chisel......really loud saw.....I've since replaced the Walker style with a modded stock 262 muffler due to the noise....

 

[chipper1]

Just sold this one.

 

[Daserlon]

There's a couple non 2 series in there, 181se and 394xp. My other 2100 and the 272's arent there either.

 

[Cantdog]

Just sold this one.View attachment 549367

Boy that looks way better than this one!!!! This 257 is from the same fella I built the 262 for.......they all look like this when he can't make them run anymore...all 4 of his 262s looked like this........LOL!!!!!