Project Stumpbroke Jonsered 2165

[Stumpys Customs]

are you building the piston up to project into the combustion chamber?

No, I leave the piston flat.

 

[Stumpys Customs]

I've got the cyl laid out for the port work. I got a lot of material to remove:msp_thumbup:

The lower transfers are quite a bit smaller than the 372.

 

[WKEND LUMBERJAK]

To bad you can't get before and after videos :frown:

 

[Dan_IN_MN]

Would an angle even be possible without cnc??

Yes you could use the compound cross feed....but would it be worth it?

Stumpy.....do you have a faceplate for your lathe?

Do you experience a lot of cutter chatter when cutting the squish band up in the cylinder from flex in the cutter bit? If you do a stiffer cutter set up can be made.

OH....BTW....nice work so far!

I guess there will not be any before porting pics on this one!

How many hours on this saw? How was the wrist pin bearing?

 

[Stumpys Customs]

To bad you can't get before and after videos :frown:

I got you covered there big guy, I got a bone stock 365 special here too. I'll get a vid of both with the same B&C.

 

[WKEND LUMBERJAK]

Not the same ones red and ones orange man are you color blind.:hmm3grin2orange::hmm3grin2orange:

 

[Stumpys Customs]

Yes you could use the compound cross feed....but would it be worth it?

Stumppy.....do you have a faceplate for your lathe?

No, I sure don't. I need to get a faceplate & a 4 jaw chuck.

 

[Steveo_supremo]

I got you covered there big guy, I got a bone stock 365 special here too. I'll get a vid of both with the same B&C.

That just won't do. Everyone knows the red ones are stronger out of the box than the orange ones. :msp_tongue: Or maybe they just feel stronger 'cause they look so cool!

 

[Stumpys Customs]

Not the same ones red and ones orange man are you color blind.:hmm3grin2orange::hmm3grin2orange:

It's not the color of the dress that matters, they are both sweedish meat under neath

 

[WKEND LUMBERJAK]

Ya I know but you know what they say about saws dressed in red they put out.:msp_ohmy::msp_ohmy:

 

[Hedgerow]

Yeah, but the German ones are genetically superior...
Man, has this thread gone south...
:hmm3grin2orange:

 

[jropo]

:msp_thumbup:opcorn:

 

[Hedgerow]

:msp_thumbup:opcorn:

I refer to the black and orange ones of course...
Not the creamsickles...:msp_tongue:

 

[Stumpys Customs]

Yeah, but the German ones are genetically superior...
Man, has this thread gone south...
:hmm3grin2orange:

I can't believe you said that:msp_ohmy:

 

[jropo]

I refer to the black and orange ones of course...
Not the creamsickles...:msp_tongue:

Ya thats pretty slick what you did there, if you can't figure out where to put the oil and gas in that one ya got issues.
I think I'd like the creamsickles better if I could ever get the things to start.:bang:
I was on the bay the other day and seen 029's and such going for 2-300, really?

Looks like Stump wants to get all them brand X saw chips covered up.:msp_tongue:

Messed up, about the bearing. :msp_ohmy:

 

[Stumpys Customs]

Got the portwork done earlier. I'm bout done puttin this thing together.

 

[Eecho]

Man I love watching these port work vids. If I still ran a mazak super quick turn id be up heaven , that is with some guidance from you pros lol. Great work btw .

 

[Stumpys Customs]

It runs!!!
I'll get some fuel through it tomorrow & a vid of it against a stock 365sp.

 

[parrisw]

Would an angle even be possible without cnc??

Yes, its very easy. Set you're slide to whatever you want, I cut my 390 at a 2° taper.

Oh BTW, nice work Stumpy.

 

[TK]

Holy oinkin Batman that pig lost some freakin weight!!!! What she weigh now, 12.5lb PHO????? :msp_w00t: