Sachs Dolmar Chainsaws Thread

[166]

.

 

[166]

These were posted at the Motorsagenportal a while back. But I don't remember who posted them.

 

[166]

 

[166]

 

[pioneerguy600]

That is an awesome amount of picts and info in those adds, mucho thanks 166 for adding all this info to this thread.
Pioneerguy600

 

[discounthunter]

That is an awesome amount of picts and info in those adds, mucho thanks 166 for adding all this info to this thread.
Pioneerguy600

aint that the truth! i learned more about S-D in those posts than i ever knew! thank you 166.

 

[Work Saw Collector]

That is an awesome amount of picts and info in those adds, mucho thanks 166 for adding all this info to this thread.
Pioneerguy600

Found it, thanks Pioneerguy.

 

[pioneerguy600]

Found it, thanks Pioneerguy.

Hope to see your 115 on here.
Pioneerguy600

 

[sawkiller]

Any of you Dolmar fans ever had any trouble with them??

I bought a new 5100 a while back and man that saw was fast!! Ran great and cut even better for about 9 months and at that point the saw might have had 40 hours on it and she siezed up one day while I was cutting!! I took it to the dealer and he rebuilt the saw under warranty and said he suspected low grade 2 cycle oil had caused the problems. I had been using dyno oil cheap stuff from tractor supply. He recomended that I use husqvarna synthetic that he sold so I bought it and a new gas can on his recomendation and mixed it religously with one gallon of gas.

Took out the freshly rebuilt saw and began using it and only had about 6 hours on it when she locked up again. Unfortunately the warranty was over and Dolmar does not stand behind their products at all when repaired at one of their facilities they suggested I take it up with the dealer. He no longer sells Dolmar and had no interest in standing behind it or his work (not sure where the problem lay).

Then the dealer says that I must have mixed the fuel wrong or used cheap oil because these saws have no problems. I must say I was furious at this comment as I had followed his directions to a tee. I then called Dolmar again only to be told that 2-cycle engines can sometimes be finiky and probably the failure was due to the Husqvarna synthetic oil and Dolmar oil would have been much better. They also said they would love to keep me as a customer but could not do anything to remedy the saw or loss of cash laid out on it.

So I am just curious has anyone else had any trouble with these or did I just get a bad one?

 

[Wildman1024]

Any of you Dolmar fans ever had any trouble with them??

I bought a new 5100 a while back and man that saw was fast!! Ran great and cut even better for about 9 months and at that point the saw might have had 40 hours on it and she siezed up one day while I was cutting!! I took it to the dealer and he rebuilt the saw under warranty and said he suspected low grade 2 cycle oil had caused the problems. I had been using dyno oil cheap stuff from tractor supply. He recomended that I use husqvarna synthetic that he sold so I bought it and a new gas can on his recomendation and mixed it religously with one gallon of gas.

Took out the freshly rebuilt saw and began using it and only had about 6 hours on it when she locked up again. Unfortunately the warranty was over and Dolmar does not stand behind their products at all when repaired at one of their facilities they suggested I take it up with the dealer. He no longer sells Dolmar and had no interest in standing behind it or his work (not sure where the problem lay).

Then the dealer says that I must have mixed the fuel wrong or used cheap oil because these saws have no problems. I must say I was furious at this comment as I had followed his directions to a tee. I then called Dolmar again only to be told that 2-cycle engines can sometimes be finiky and probably the failure was due to the Husqvarna synthetic oil and Dolmar oil would have been much better. They also said they would love to keep me as a customer but could not do anything to remedy the saw or loss of cash laid out on it.

So I am just curious has anyone else had any trouble with these or did I just get a bad one?

Welcome to the site. Sorry to hear about your 5100. If you do a search on here you will see there are a few people who have had issues with them but the majority of those issues seem to be with saws incorrectly set up or just not set up right from the dealer. It seems the 5100 is a great saw if tuned correctly.

 

[mowoodchopper]

awesome thread !!!!!!!

 

[bigjohnston]

great group of ads

 

[Yoopermike]

I have a dolmar 116si... great dependable saw .. I plan on buying a dolmar 5100s in the near future.. and maybe a couple dolmars in the distant

 

[leeha]

I have a dolmar 116si... great dependable saw .. I plan on buying a dolmar 5100s in the near future.. and maybe a couple dolmars in the distant

The 116SI as well as the 120SI are
fantastic saws in there time. I still use
them for all my firewood cutting.


Lee

 

[bigjohnston]

know what ya mean my 120 is a mean little saw, the 116 unfortunately has low compression

 

[mowoodchopper]

know what ya mean my 120 is a mean little saw, the 116 unfortunately has low compression

You can get new piston rings, even cyl for the 116si, I can get them local

 

[pioneerguy600]

Got myself another project saw, it`s a 133 and needs a few parts to get er up and going, otherwise it`s in good physical shape.

Pioneerguy600

 

[HuskerDolmar]

I have a 115, a 6000, and a 133. The 6000 was the first saw I bought, and really probably all the saw I need 90% of the time.

 

[pioneerguy600]

Rounding up some parts for it with some on the way and a search on for a few more, will keep this site updated. Couple more picts,

Pioneerguy600

 

[jockeydeuce]

WOW Jerry!!! No wonder you want to fix that 133!!! What a clean saw!!.....Nice score!!