komatsuvarna
Arboristsite MVP
This all came from the air filter and air box on one TS420 cutoff saw I serviced today....
Last edited:
What's On Your Bench? 2/15/13
- Thread starter Mastermind
- Start date
Help Support Arborist Forum:
Rudolf73
Addicted to ArboristSite
This all came from the air filter and air box on one TS420 cutoff saw....
I'm guessing it didn't run so good...
Brad, gonna have to feed them a little more before they are filet'n size, too small to fry or make a gumbo with right now.
I had a poulan 475 shipped from a site member here and it was PHO with no tank in a Empty box :msp_confused:. About cried when I seen the right rear AV mount broken off. Dumbazz 
I rednecked fixed for now and it's holding great. But I know who will get it done right the next time around IF needed.
I rednecked fixed for now and it's holding great. But I know who will get it done right the next time around IF needed.
komatsuvarna
Arboristsite MVP
No it ran fine actually, used it last on Friday. The ts420 has a good air filter system, the best out of all the others we've tried IMO. I was amazed to see that much #### come out of it...it hasn't been neglected either lol.
So how did that packing job hold up on the 325? :question::fingers-crossed:
I still dont know how it weighed 10lbs more then most of my shipments. Must have weighed it while my arm was still relaxing on box.
Yep, 325 was packed just fine, nothing broke so it was fine.......
cobey
Addicted to ArboristSite
108 dolmar ...resting in peices :frown: I cleaned it and found out it had a case repair that messed up where the spikes were supossed to be, bad oil pump,
good compression.. bad crank seals. would sell it but its worthless because of shipping
and 2 xl12's one locked up, one in peices trying to get it to run but it really needs a complete teardown
and im not sure how much i want to put in this saw, they had a hard life!!
good compression.. bad crank seals. would sell it but its worthless because of shipping
and 2 xl12's one locked up, one in peices trying to get it to run but it really needs a complete teardown
and im not sure how much i want to put in this saw, they had a hard life!!
komatsuvarna
Arboristsite MVP
Haha, Just realized this isn't 2-15-13 !!
I gotta get with the times lol!
I gotta get with the times lol!
brad,
that orange sichlid you have will get BIG, and before you know it all your little fish will be gone..
i've had 2 of em, they both died of old age (i think) by old age, i mean about 12-13 yrs..
the largest of the two was about 2" thick, 8" long, and about 6" high..... he/it barely fit into a 2LB coffee can when i "fished" em out...
they get really aggressive too...... like, try (and succeed) to bite your hand/fingers when your in there...
logging22
Cuttin to live, livin to cut
Big azz Hornet! Heavy weight, old school, PIA. It does run, but having carb issues. Have my feelers out in another thread for help.:msp_tongue:
procarbine2k1
Addicted to ArboristSite
Cleaned shop today. Got half a dozen or so saws out and fired up (weather was nice). Clutch tool came in for the 1050 Super, so I will more than likely check that out this week.
Just finished a Stihl 015AV, wired up a new kill switch, 4 more to go. Stihl 032-putting in ignition chip which I'm waiting for, I hope the Nova II will work. Homelite VI944, leaked fuel and weak clutch springs. Skil/Poulan 3400 just needs cleaning up and maybe a new air filter cover. Husqvarna 350, new ring and gotta find a few minor parts which I didn't get with the saw. None of these are big hurry items, fix them when I feel like it. I've got about all my trees cut up and firewood for a couple more years.
2Twannabe
ArboristSite Operative
What are you using to fab the muffler reed?
Rudolf73
Addicted to ArboristSite
Nice! What are those angley bits for with the wing nuts on them?
Those have a small diamond tip on them and they are used to dress the grinding wheel to the desired angle and width. There is alot of little settings on this thing, but once it is dialed in it sure makes a nice chain.
Yes Young I got it about 2 weeks ago. I hand filed a couple of chains from round ground chisel to square and got hooked on the cutting ability of the chain. So I sprang for a square grinder.
Simington 451c
cool beans. didnt want a silvey?
