P.S. This new coil was quite inexpensive on our favorite auction site. Seems to be a healthier market for old outboard parts than chainsaw parts.
Chris B.
Chris B.
Pioneer chainsaws
- Thread starter WesternSaw
- Start date
-
- Tags
- operator manual
Help Support Arborist Forum:
had to do some customizin on the pioneer laminate to get the mac coil on. theyre not only too fat, the legs are too close together. grindin on all 3 legs. I gots more time than $$$, cbf's way prolly easier.
ML12
ArboristSite Guru
Has anyone ever replaced the primer on a 3200 with one of the bulb types? if so can you post a picture? thanks!
p61 western
ArboristSite Guru
Not much help but I put a carb with a choke on my 1110 and it works great.
I have a 3270SC. I can take a pic or two of the air box, carb etc., if you are wanting to swap to a choke system.
Working on trying to get past a failed ignition on an early big P series I picked up recently. A bit of experimenting going on.
Took 3 days of soaking in gasoline to get all the pitch off the chain. Original chipper and lots of life.
Took 3 days of soaking in gasoline to get all the pitch off the chain. Original chipper and lots of life.
p61 western
ArboristSite Guru
What p series is it with the failed ignition?Could you share on the experimenting.
ML12
ArboristSite Guru
That would be great thanks!
CBfarmal adopted a 3200 I had. It had a Poulan type primer bulb adapted to it. Worked. Even the screw size/spacing matched.
But I don't recollect how the fuel line were run.
Fat Alice lost her spark. Cleaned the points and now have a weak spark.
Condenser? Coil?
Runs but is shooting ducks (ignition miss).
Condenser? Coil?
Runs but is shooting ducks (ignition miss).
Here you go. Carb is a HS-146A. Semi-fixed high jet. Same as the HS-151's on some of the 92x series Homelites.
ML12
ArboristSite Guru
I'm trying to track down some oil seals for the 3200 and haven't had any luck with motion Canada, my usual go to. The pioneer part number is 427656. Has anyone got a modern equivalent? Tia
Do you have a seal out so you can measure the case bore on the dia of crankshaft where the seal rides?
ML12
ArboristSite Guru
Yeah pulled the seals. 15mm shaft with a 1.125" od and they are 5mm thick it's the od that is a problem. Standard sizes are 28mm od and then 30mm od.
These should fit. Double lip (dust seal), metal case
The width (depth installed) is 0.312". You would have to make sure there is enough room in the case pocket.
Same dimensions on both.
Your shaft is 0.591" These are listed for that size as well as 0.593"
The OD is 1.128" on the seal which fits a 1.124" nominal bore. TCM used to make 28.58mm bore size seals but don't seem to anymore.
Timken 471532 and
Daemar S05911231BS
S05911231BS
Type
Oil Seals Inch Series
I.D.
0.593 in
O.D.
1.125 in
Seal Width - W
0.312 in
Profile
BS
Material
NitrilePASiliconeViton
The width (depth installed) is 0.312". You would have to make sure there is enough room in the case pocket.
Same dimensions on both.
Your shaft is 0.591" These are listed for that size as well as 0.593"
The OD is 1.128" on the seal which fits a 1.124" nominal bore. TCM used to make 28.58mm bore size seals but don't seem to anymore.
Timken 471532 and
Daemar S05911231BS
S05911231BS
Type
Oil Seals Inch Series
I.D.
0.593 in
O.D.
1.125 in
Seal Width - W
0.312 in
Profile
BS
Material
NitrilePASiliconeViton
Good work as usual Tim. I am not up to speed on this aspect of the game.
I should be swapping out the seals on my machine as well. That 427656 is for the FW side only? Do you have the measurements for the 428746 on the PTO?
I should be swapping out the seals on my machine as well. That 427656 is for the FW side only? Do you have the measurements for the 428746 on the PTO?
The 428746 is the large P series seal.
Use SKF 5606 double lip or National 472705 double lip Nitrile
Fits bore size 1.00 inch and shaft size 9/16"
p61 western
ArboristSite Guru
Great info as always.I was just looking for some today, and everywhere said nla for the pioneer/poulan part number.
astnmacgto
Carnac The Magnificent
Dumb question from a mac guy to you pioneer collectors, my dad has a model 650 pioneer, but I believe it's white bottom instead of yellow like I've seen on google, does this mean anything to you guys?
Similar threads
- Locked
