Sure is quiet in here....do I need to start a fight?

[BigDaddyR]

Morning slakizens.

Long day today and tomorrow. End of the month is always a beeyoch.

My now running Hooskie 36 has a few issues. It goes crunch when I pull the chain around. Looked at the IPL and figured out they were running a new bar and chain for 3/8 on a .325 sprocket. Worn to say the least. Still usable for light doody?

3/8 spur NLA so looks like I'll go new/used .324 b/c. Also needs starter pulley. Starts but kinda krunchy sometimes. Pulley is worn. Guess I'll pressure test it also when I put a new sprocket on. Pulley is like $4 so cheap enough. Make sure seals are good.

Bearings. No real play laterally with saw on its side but about 1/16 up and down when pulling up towards the ceiling on flywheel. Normal?

View attachment 306761

Sorry to blab so much at the breakfast bar but limited time to access today.

Get er dun!


Sent on the fly.

 

[BigDaddyR]

I was out pulling weeds yesterday. LOL Could be where I got this one ? Plus I put the same pants back on this morning ?

Sounds like me. Lol.

Oh yeah. Carb settings. The 36 has a WT-202 carb in it. High is set 1 turn out and low is 1/2 turn. Little lean on the low side? Starts but about 4-5 pulls.


Sent on the fly.

 

[roncoinc]

Morning slakizens.

Long day today and tomorrow. End of the month is always a beeyoch.

My now running Hooskie 36 has a few issues. It goes crunch when I pull the chain around. Looked at the IPL and figured out they were running a new bar and chain for 3/8 on a .325 sprocket. Worn to say the least. Still usable for light doody?

3/8 spur NLA so looks like I'll go new/used .324 b/c. Also needs starter pulley. Starts but kinda krunchy sometimes. Pulley is worn. Guess I'll pressure test it also when I put a new sprocket on. Pulley is like $4 so cheap enough. Make sure seals are good.

Bearings. No real play laterally with saw on its side but about 1/16 up and down when pulling up towards the ceiling on flywheel. Normal?

View attachment 306761

Sorry to blab so much at the breakfast bar but limited time to access today.

Get er dun!


Sent on the fly.

Include a not on 36 parts with the carb,,i think i have some ?

 

[tbone75]

Morning slakizens.

Long day today and tomorrow. End of the month is always a beeyoch.

My now running Hooskie 36 has a few issues. It goes crunch when I pull the chain around. Looked at the IPL and figured out they were running a new bar and chain for 3/8 on a .325 sprocket. Worn to say the least. Still usable for light doody?

3/8 spur NLA so looks like I'll go new/used .324 b/c. Also needs starter pulley. Starts but kinda krunchy sometimes. Pulley is worn. Guess I'll pressure test it also when I put a new sprocket on. Pulley is like $4 so cheap enough. Make sure seals are good.

Bearings. No real play laterally with saw on its side but about 1/16 up and down when pulling up towards the ceiling on flywheel. Normal?

View attachment 306761

Sorry to blab so much at the breakfast bar but limited time to access today.

Get er dun!


Sent on the fly.

I have some new small Husky starter covers,not sure what they fit ? Or exactly where they are ? LOL I will look.
Don't think the crank should move that much ? May be a problem ?

 

[tbone75]

Sounds like me. Lol.

Oh yeah. Carb settings. The 36 has a WT-202 carb in it. High is set 1 turn out and low is 1/2 turn. Little lean on the low side? Starts but about 4-5 pulls.


Sent on the fly.

May need a little more on the L side. Does it rev right up , or stall a little ?

 

[BigDaddyR]

Include a not on 36 parts with the carb,,i think i have some ?

Will do. Was having the wife send it this am but will drop a note in there tonight and send in am tomm. Let me know what you need for things or I might have minor trade fodder. Doubt I have anything you don't buy you never know.


Sent on the fly.

 

[tbone75]

The OL has a job interview today at the place beside her old job. Hope she gets it !!

 

[BigDaddyR]

May need a little more on the L side. Does it rev right up , or stall a little ?

Revs most times but sometimes you have to feather the throttle a little to get it to not bog and then it will take off. I'll fatten it up 1/8-1/4 turn and see how it does.


Sent on the fly.

 

[BigDaddyR]

The OL has a job interview today at the place beside her old job. Hope she gets it !!

Me too. I'll keep my fingers crossed for her.


Sent on the fly.

 

[tbone75]

Will do. Was having the wife send it this am but will drop a note in there tonight and send in am tomm. Let me know what you need for things or I might have minor trade fodder. Doubt I have anything you don't buy you never know.


Sent on the fly.

That B&C should be OK to use.

There shouldn't be any up and down movement on the crank .

 

[tbone75]

Revs most times but sometimes you have to feather the throttle a little to get it to not bog and then it will take off. I'll fatten it up 1/8-1/4 turn and see how it does.


Sent on the fly.

That should fix it.

And start easier !

 

[AU_K2500]

Russell won't be working this weekend so no dice on heading out there. It works alternating weekends and I got thrown off. Push it out a week?



Jimmy

OK, sounds good.

 

[tbone75]

Wonder who makes Toro whackers ? Need a tank grommet. Don't look like any I have round here ?

 

[tbone75]

WOW , its only 8:30 and I am ready to get moving !

Back to whacker hell ! :hmm3grin2orange:

 

[BigDaddyR]

That B&C should be OK to use.

There shouldn't be any up and down movement on the crank .

Problem is chain is 3/8 on a .325 spur. Can I use the bar with a .325 chain? If so then only need chain which is easier.


Sent on the fly.

 

[tbone75]

Problem is chain is 3/8 on a .325 spur. Can I use the bar with a .325 chain? If so then only need chain which is easier.


Sent on the fly.

Only if its a hard nose or a 325 bar. If its a 3/8 bar the sprocket tip won't fit the 325 chain.

 

[roncoinc]

That B&C should be OK to use.

There shouldn't be any up and down movement on the crank .

Sounds like he has the saw on it's side,and that would be in/out movement,little aint to bad.
if saw was sitting upright and had up/down play,bad..

 

[IEL]

WOW , its only 8:30 and I am ready to get moving !

Back to whacker hell ! :hmm3grin2orange:

Whackers suck..... LOL

 

[tbone75]

Sounds like he has the saw on it's side,and that would be in/out movement,little aint to bad.
if saw was sitting upright and had up/down play,bad..

Wasn't sure if he meant in/out or up/down. LOL

 

[roncoinc]

Kid got here 8am sharp to split wood.
moved splitter and pulled on starter,almost broke my wrist !!
hydrolocked !
pulled plug and gave it a yank !!
dummy me !! was standing on fron of plug hole !!!
GOTTA shut the fuel off on them things when moving them !!
second time this happened on me..
fuel in bowl gets swishin around,float lowers,more fuel comes in,ends up pouring down intake into cyl,fills cyl,no pull !!
checked oil,good and clean,no gas in it,meens good rings eh ?
only a couple minits,didnt have much time to leak by.