Project 084 Nears completion

Freakingstang · Nov 22, 2006

I've been working on an 084 project saw for a while. I bought one that was pretty rough, but the piston and cylinder were in great shape. Found another donor parts saw along the ways. I ended up using this case as I found a few stripped holes in the other one, So here are some pics of what I started with....

Freakingstang · Nov 22, 2006

Here are a couple more pics of the good fuel tanks I got.

Check out the size of that carb!!!!

Freakingstang · Nov 22, 2006

Well, Here are some of the better pics.. I sanded down the case and the covers. I had to do a little JB weld to the clutch cover as both the ones I had had some pretty bad breaks and cracks in them. This was painted using the Stihl Grey paint

Freakingstang · Nov 22, 2006

Cut4fun said:
Steve, How do you get your project saws so clean before working on them. I have been working on another 5000 plus and it is covered in 1/8 inch of pine sap wood dust etc. It is hardened to where it takes a scraper to remove it, but I dont want to scratch up the paint and dont want the stickers coming off. Ideas?

What part of don't post a reply didn't you understand.....

I use a pressure washer and some differant cleaners. The hot water and high pressure work good. I try to soak them for a couple hours to help loosen the grime

Freakingstang · Nov 22, 2006

here are some more....

Cut4fun · Nov 22, 2006

Freakingstang said:
What part of don't post a reply didn't you understand

Didnt know you was going to post a book. So F@$% you bud. :jawdrop: LOL. Thanks for the info. You never have had prob with water getting in a seal from the pressure.
I will go delete the in between one.

04ultra · Nov 22, 2006

Looks like its coming along fine.. Cant wait to hear how it runs..Hope it runs like mine you'll be real happy.. :cheers:

..

..

Cut4fun · Nov 22, 2006

Read the whole thing Andy, I did go delete it. Was yanking the young dawgs chain. :dizzy:

Freakingstang · Nov 22, 2006

I ordered some more parts the other day..

I got a new top cover, HD air filter cover, the decal plate for the starter cover, and all the rubber lines, bushings, etc

Cut4fun · Nov 22, 2006

Is that the off white-grey stihl paint? Looks real grey in the pics. Thought about the 066 RL for a touch up, but looks like a scarred warrior the way it sits.

Andy1234 · Nov 22, 2006

Ummmm...I don't think they were THAT clean when new!!! :cheers:

Looks nice, Steve!!

Andy

:notrolls2:

rahtreelimbs · Nov 22, 2006

Steve, you have any problems with gas dissolving that Stihl paint? The one and only time I used it it happen to me.

Can that paint be baked?

blsnelling · Nov 22, 2006

Nice work Steve. I like to do work like that but usually get too impatient for the "pretty" stuff.

Lakeside53 · Nov 22, 2006

I always bake it... 225f for about 30 minutes... in a convection oven - not radient heat, or a month in the green house... Once it's hard and really dry, it's reasonably gas resistant.

Freakingstang · Nov 22, 2006

rahtreelimbs said:
Steve, you have any problems with gas dissolving that Stihl paint? The one and only time I used it it happen to me.

Can that paint be baked?

This is still not fully assembled, so I can't answer that, But Lakeside recommends baking the paint otherwise it really soft for about a month.

I set these parts infront of a radiant heater for about 2 days and then they sat by the stove for a few more days.

The more heat you can get, the better it dries and sticks....

Cut4fun · Nov 22, 2006

I wonder if Talon owned that saw before? Looks like it took a hit on the top side before steve got it:hmm3grin2orange: :biggrinbounce2: .

Freakingstang · Nov 22, 2006

Cut4fun said:
I wonder if Talon owned that saw before? Looks like it took a hit on the top side before steve got it:hmm3grin2orange: :biggrinbounce2: .

Nope, but at least my garage didn't have a mishap with Talon and a tree removal......

rahtreelimbs · Nov 22, 2006

Freakingstang said:
The more heat you can get, the better it dries and sticks....

Get it to the oven before the ol' lady catches on!!!:hmm3grin2orange: :hmm3grin2orange: :hmm3grin2orange:

RiverRat2 · Nov 22, 2006

nice work

Those are really awesome saws, from tha looks of it you are well on your way Keep us posted :rock:

IVe got a couple of 066's that i bought the paint for and I have not got them clean enough yet,,, good Idea with the steam cleaner,,,, did you take it all the way down to clean metal or did you just feather back the edges to where the paint was still stuck good??????

Cut4fun · Nov 22, 2006

Freakingstang said:
Nope, but at least my garage didn't have a mishap with Talon and a tree removal......

That was God's way of giving me a new garage and paint jobs. Thank God for 100mph winds.:hmm3grin2orange: :biggrinbounce2: Even bought the wife a new Monte with all the insurance money. Like I say, everything happens for a reason.
At the time it looked and smelled like poop. But boy it sure smells good now.

Project 084 Nears completion

Help Support Arborist Forum:

Doctor Freakinstein

Doctor Freakinstein

Doctor Freakinstein

Doctor Freakinstein

Doctor Freakinstein

Faster is Better

"Out of Control"

Faster is Better

Doctor Freakinstein

Faster is Better

ArboristSite Operative

A.K.A Rotten Tree Limbs

Goosme!

Stihl Wrenching

Doctor Freakinstein

Faster is Better

Doctor Freakinstein

A.K.A Rotten Tree Limbs

Serio Tree Freak

Faster is Better

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!