echo

Hey team I’d love to run a Stihl bar with a rounder nose sprocket on my ported Echo cs4010 that I love for piecing trunks on my way down. This one has the same specs as the skinny Echo bar I’m running, with an adapter to mate the mounting bolts it should work, right?

I have a kioritz echo cs302, I'm not 100% on the year, Was wondering if anyone knew a way to find out the exact year of manufacture.

I recently purchased a "lightly" used Echo CS-590 from an older couple (still had the security tag stuck to the bottom). I took it home and put fresh 50:1 in the tank and fired it up. It popped right away but would only stay running past half throttle. Anything less than half and it would stall...

My oil cap is leaking from, what I know as the "oil breather" hole. Is there meant to be a piece of hose coming off it or some sort of valve? Leaks sitting cold. Thank you!

SPEEDCUT NANO CONVERSION KIT, 14" - ECHO CS-355t Not yet.... :reading: but maybe with your help... Someone said to me the other day "Oh you gotta put the Nano on that saw..." I had just told them I was buying a new cs-355t and planned to do a little work to it to wake it up. My name is Matt...

SPEEDCUT NANO CONVERSION KIT, 14" - ECHO CS-355t Not yet.... :reading: but maybe with your help... Someone said to me the other day "Oh you gotta put the Nano on that saw..." I had just told them I was buying a new cs-355t and planned to do a little work to it to wake it up. My name is Matt...

I am going to purchase a new Echo CS620P. just thought I’d reach out and see it anyone knows of a discount code for sawsuppliers.com or any other good place to purchase. I tried to buy one from 2 local dealers. First place the “showroom” was so dark and dingy I couldn’t see what was on the...

Hello, The clutch will not come loose so I can remove and replace the DRUM and now cracked clutch. I used a rope to stop the piston, turned it right to loosen. Its so seized I’m afraid any more pressure will cause too much stress on the internals. any suggestions welcome

Hello everyone. I just bought an echo 355t for a basic climbing saw. Are there any recommendations to impove the saw beside muffler mod. Any input is appreciated.

Hello my good fellows and lasses, First post, been lurking a while though...hopefully this thread is soisted in the right spot...on to the meat and potatoes! I have an Echo cs3510, maybe 20 tanks through it, that has taken to interpretive dancing a paper weight. The numbers: 120 psi cylinder...

I purchased a used echo cs310 with bad clutch, sprocket and bar studs. Replaced all and could not get it to oil. pulled everything off again and saw this. I forgot to take a picture prior but the worm gear was broken and stuck in the plastic housing. I tried removing as much of the charred...

Thanks for letting me join! Homeowner here, Echo CS-400 and CS-4910, and old Husqvarna 191! Lots of great info and advice here- looking to learn a lot about chainsaw maintenance and repair!

Echo Twin Cylinder chainsaw, starts and runs good, idles, oils and cuts good, bar and chain are in nice condition, starts pretty easy but doesn’t get started very often, has small crack on rear handle. Have more pictures available as well. Asking 400 , local pick up available in Brownsburg Indiana.

Selling my Echo CS2511T saw is still all stock. I bought it new about a year and a half ago, have ran about 20 tanks of fuel through it now, I always run 40:1 mix. Saw starts and runs fine, but I'm sure it"ll need a tune to make it just right. Only issue is the purge bulb is cracked, so it's...

pics of full size images on page two. If you would like the soft starter handle it's here with the original rope on it although a bit dirty and worn some. This rope is new with used OE pull handle. Enjoy I know, bla bla bla but I'm not logged in on my phone. This tool is low hours from the...

I just go the saw and it ran great.After cutting for about an hour it suddenly shut off,no bogging,no signs that it was going to shut down.it has spark.Please help me out

First saw of my own, I’m hooked and ready to get more! I’ve cut a little with it but can’t wait to really put her to work! Love these 1127 series saws! These babies are tanks!

Hey everybody, new here and new to this subject as well but looking forward to learning all I can. To start o have a question regarding a potential purchase of a couple of old chainsaws local to me with a mind to learning about small engine mechanics and chainsaws. There's an ad offering 2 Echo...

Hello I'm having trouble finding an after market piston for and echo cs341. I don't have the saw physical in hand but I bought it online and am trying to get parts ordered before it arrives. Does anyone have a clue what size piston It is or what saws share the same piston?

Hi all, I recently bit the bullet and installed a Little Red Barn POP-UP Echo CS-620P piston in my Echo CS-590 Timber wolf, along with a Walbro WT-216 and unlimited Oppama coil, after getting it dialed in it runs really good, I was unable to slip the clutch with a 20" bar with a full comp 7/32"...