husqvarna

We bought a new house on almost an acre, half of which has lots of large mature trees and several massive unearthed stumps and rounds from previously felled trees. I'm also a novice woodworker. I'm looking to potentially pickup a chainsaw secondhand to use for clearing and pruning, as well as...

Thought I'd share my video and tips on why a saw won't start!

My Husqvarna 460 Rancher, 24" chain, is not letting oil get to the chain. I repaced the metal oiler, the plastic oiler drive gear and the rubber distribution tube, but it didn't make any difference. I have the oiler set to it's highest setting, (turned counter clockwise to its third setting)...

Hi.I have a Husqvarna 236 recently rebuilt, but i have an issue.Saw starts only with choke once it's hot.Should i tune the carb again?Wich screw?

Hi there I am wondering if anyone can advise me regarding a husqvarna 65 I am rebuilding I bought this saw as a project build having just completed a rebuild on a 254xp (1995). And so far the posts on arboristsite have been a well of helpful info for both the current and previous projects The 65...

Well my first time selling in a long time..... Jonsered CS2145 chainsaw. Saw was completely broken down and rebuilt and brought to Jonsered CS2152 specs using the best factory parts. This saw does not have the magnesium cases of the 353/CS2152 saws. They use the same piston and cylinders of...

i have a beautiful 181se im trying to get running good, i noticed when replacing the fuel line that the plastic inlet on the carburetor could be moved up and down, is this common or is something loose? It does have a weird run condition and the saw doesnt look like it was used enough to have a...

Trail maintenance hike video.

Anyone know what cylinder this is? 266? Thanks.

Hey all, First off, thanks for being here, it's been helping out a whole bunch, especially if you're a nostalgic fool and too stubborn to buy a new saw ;). Nonetheless, ran into an issue where the interwebs is unable to give me a straight answer. Recently bought a Husqavarna 266SE, runs fine...

Hi guys, Happy holidays! I'm new to this site, and must say the amount of knowledge here seems vast, glad to here! Anyways; got my hands on an older 3120. The saw is bought as the large companion to my existing 460, which I've had for 10 years, taking down primarily beech and oak of sizes...

Im needing a new clutch spring for a Husqvarna 181SE. Is the early 281 spring with a different number the same? Also was there a guide bar plate on the clutch cover or was it just the wear pads?

Recently purchased a file guide kit at Walmart the brand is trilink come with 1 file guide and 5/32 , 3/16 , 7/32 files for best results should I have picked up separate guides for each file , thanks for any help

This saw is in excellent condition I just had it gone threw had the carb rebuilt the oiler changed new gas lines you can call or text @ 3853094556 with questions.

as title says I am looking for a good used Husqvarna 394XP piston. Also looking for a 181/281 piston. Not the thin ring one!

Up forsale is a 394xp with new meteor piston, carb kit, am muffler, ports have just been cleaned up. Gasket, heat shield, muffler and cylinder all been matched. Base cut so squish is around .024". Muffler has had three ports drilled in front, spark screen fitted for those three holes. THIS SAW...

Got a Husky 371XPG. Took out the carb to rebuild and I notice this wire snipped at ground, but then a snipped wire back a ways too. No, wire won't stretch to reach. It seems like someone took a segment out of it. Or, its 2 separate wires. I got this saw from my dad. He didn't know anything about...

The other day a guy from work called me up, because he was having problems with his 435 Husky. He said it sat for several months (apparently somewhere moist cause the bar and chain had fresh rust) and got it out to do some work around the farm. According to him he got it fired up and then it...

So I got a Husqvarna 350 for $100 non running as is. I thought it was a decent deal so I went ahead and picked it up. Now I've started tearing it down for a rebuild and wanted to get some opinions on what route to take I see a lot of people building them into a 346xp, I'm leaning towards this...

I purchased this saw from a member here (04titanse) a few years ago and it's been great to me. This saw didn't get much use but boy was it fun! Aside from milling 3 logs (two of them were under 12" diameter and one was about 24"), it was used under normal conditions if you don't count the bee...