200T Carbitooter Thread **Official**

[angelo c]

Really, that sucks.

that I can't get them to work or that I will have to pay the duty fees when you send them back all working and all better....

hehe...

let me know if you find the check in the box....hehe.!!!!

 

[parrisw]

that I can't get them to work or that I will have to pay the duty fees when you send them back all working and all better....

hehe...

let me know if you find the check in the box....hehe.!!!!

Send them if you want, unmolested carbs only!

 

[angelo c]

Send them if you want, unmolested carbs only!

aww shucks I figured the Molestered ones would be good for a few laughs...

 

[Zippy]

Me too!

I had really good results following advice on this thread - got two MS200t's back into service, one for a tree surgeon.

 

[NewToStihl]

Well, the accelerator kit fixed it for $8.50. We'll see how long it lasts. Thanks to everybody for the info.

Maybe I missed something, and if so I apologize, but what exactly is the accelerator kit, and where can I get it? I don't see it in the IPL nor anywhere on ebay?

My 200T is having throttle response issues and it sounds like this will help me as I have the same carb. Thanks!!

 

[Zombiechopper]

PS. Can one of the mods change the spelling so a newbie can find it in a search ?

I very specifically named it so that it could be found in a search. Or so that I could find it

try searching '200T carburetor' and see what you find The search engine will grab carbitooter without a ton of other junk though.

edit: just tried searching '200t Carb' and it found 846 threads LOL!

 

[LowVolt]

So last fall I dumped the fuel out of my 200t and ran it out of gas. Just put gas in it tonight. It pops on full choke, runs on half choke half throttle but as soon as I hit the trigger to kick it down to idle it dies. I know the carb is a zama c1Q series but not sure of the exact model. Do I try this epoxy/jbweld method?

 

[lone wolf]

Just tried the Jb weld on the passage and removed the pump the saw works great. I don't notice any lack of throttle response. Anyone need help with this ?

 

[ptjeep]

Heres a thread i did with step by step pics of the process. Guess i should have posted a link to it when i did it.

http://www.arboristsite.com/chainsaw/238372.htm

 

[lone wolf]

Heres a thread i did with step by step pics of the process. Guess i should have posted a link to it when i did it.

http://www.arboristsite.com/chainsaw/238372.htm

I drove the brass plug in with a punch and it came out the hole on the side. Don't go to far or it will get stuck below the hole go slow . And just a little JB weld dont go crazy.

 

[dl5205]

Bumped for reference.

 

[dingeryote]

Old school Tagosis.

 

[ZeroJunk]

Well, the tree service customer brought the 200T back where I had replaced the accelerator pump in Dec 2011. It was shot again. I asked him how much he had used it and he said a lot whatever that means. Anyhow, since the carbs can be had for $88 I just replaced the carb. Since I had red loctited and peened the screws I was afraid to try it again anyway.

 

[lone wolf]

I delete it and seal it off. Still running.

 

[lone wolf]

 

[stihl038x2]

Just wondering if the pics for this thread are available elsewhere ? I can't see anything.

Steve

 

[lone wolf]

Just wondering if the pics for this thread are available elsewhere ? I can't see anything.

Steve

 

[lone wolf]

Can you see the pic in the post before this?

 

[stihl038x2]

Yours are the only ones I can see. However I did find another thread ,200t Caruretor accel pump block off, which has pics.

http://www.arboristsite.com/community/threads/200t-carburetor-accel-pump-block-off.238372/

Steve

 

[lone wolf]

You don't need to do all that just pick the plate out of the passage like in my pic clean and JB weld the port shut simple. Nothing else.