Huztl MS660

[HoosierS]

I just sent an email to check the status of my order I made last night, making sure it wasn't lost and got this email back within 5 minutes just now.

"Dear sir,Thanks for your business.Our site www.huztl.net is getting a problem with the domain agent, but we believe it will be resolved within the next couple of days, the orders placed withhuztl.net will be processed without any problem. Please do not worry about that.Best regards,Lynn"

Also noteworthy, if you look at the header on the new farmertec site it says huztl.net on the right side. So hopefully all is well with the chainsaw people in China and we'll all still get our parts.

 

[tbohn]

Well, got my 660 on the bench and see if you can spot the air leak! View attachment 549070

My compression releases leaked.

 

[Bedford T]

The base.

Be careful with the case magnesium is soft. I had a leak in same spot. Stripped the bolt and my hands are weak.

Make sure your gasket is right side up. If it is apply some dirko. If it's the bolt use a helicoil. Normal install trial.

Let it dry. Remove the carb after clamping your fuel hose off and raise the piston and allow to dry overnight before removing the jug. It looks like you cut some wood you might want to blow the dust off

Take a deep breath if needed.

 

[Bedford T]

I just sent an email to check the status of my order I made last night, making sure it wasn't lost and got this email back within 5 minutes just now.

"Dear sir,Thanks for your business.Our site www.huztl.net is getting a problem with the domain agent, but we believe it will be resolved within the next couple of days, the orders placed withhuztl.net will be processed without any problem. Please do not worry about that.Best regards,Lynn"

Also noteworthy, if you look at the header on the new farmertec site it says huztl.net on the right side. So hopefully all is well with the chainsaw people in China and we'll all still get our parts.

The workers don't know what's going on. Use the email get your tracking number write it down and move to new site farmertec.com

 

[a. palmer jr.]

Did you delete the cylinder gasket?

 

[tbohn]

My compression releases leaked.

Didn't see the bubbles the first time. I always use Motoseal 1 even if I install a base gasket.

 

[Ash UK Chopper]

The base.

Yes, correct! Bubbling like mad on the side pictured. Sprayed everything I could to make sure nothing else is leaking and all good.

The bolts are tightening down fine, no problem there. The base of the pot seems flat and the gasket seems fine. I was using a non setting gasket jointing compound.

Does that dirko stuff set or is it non setting.

Could someone confirm which way up the gasket should be please.

Getting there....

 

[Bedford T]

The indentation goes down into the case. Kinda like a bowl with cereal in it if you use your imagination. Dirko is rubbery and sets.

 

[Ash UK Chopper]

The indentation goes down into the case. Kinda like a bowl with feral on it if you use your imagination. Dirko is rubbery and sets.

Gasket is right way up then.

I assume I was right in putting jointing compound on the case only, not the pot side as well?

I'm using hylomar blue to seal surfaces

 

[Bedford T]

Both sides for me

 

[Bedford T]

Hylomar is awesome stuff in that area use dirko. To put the case together go hylomar and similar

 

[Bedford T]

 

[Ash UK Chopper]

Hylomar is awesome stuff in that area use dirko. To put the case together go hylomar and similar

I coated the crank case halve gasket in hylomar and the head gasket one side.

I'll get a tube of a setting compound tomorrow and double coat for extra pleasure!

 

[Bedford T]

You know paint thinner will dissolve blue right off that gasket if you go that way

 

[Ash UK Chopper]

You know paint thinner will dissolve blue right off that gasket if you go that way

Brake cleaner has got it clean again ready for a lubing

 

[Bedford T]

Your close, so close

 

[Bedford T]

I coated the crank case halve gasket in hylomar and the head gasket one side.

I'll get a tube of a setting compound tomorrow and double coat for extra pleasure!

dont pile it on. the thickness could throw the clearances off, the right term eludes me. use an even thin coating. the squish!

 

[dswensen]

When did you get a tracking number? When I ordered (6 days ago), all I got was a payment confirmation from Paypal.

The workers don't know what's going on. Use the email get your tracking number write it down and move to new site farmertec.com

 

[Bedford T]

Check PayPal for the tracking number if they bonk it up. They are on other side of world. I think they are a day ahead and around 12 hour difference.

I have been uneasy just like you. They did not answer a bunch of emails and their excuse was a manager left with the password.

All that is detailed In The thread. Theirs is a different world. We have different expectations.

You will not get cheated if you do and the manager leaves with all the parts this time tell paypal and you will get money back.

I bet it's just their methods that has alarmed you. Trust PayPal and go enjoy your weekend.

I don't think any of the workers know about half of what goes on. I image they just get up and leave at the set hour without regard for notices of change or holiday to the customer

 

[Ozhoo]

When did you get a tracking number? When I ordered (6 days ago), all I got was a payment confirmation from Paypal.

Take a look at your paypal receipt and you'll see an invoice number. Email [email protected] with your invoice number and ask for an update. More than likely it's already shipped.