laser bar and chains

[ammoaddict]

I like my bar, it’s heavy, and isn’t showing any abnormal wear after two chains. I can’t compare it to any other long bar because this is the only one I’ve ever run. For the money and the amount I use it I have no complaints.

Thanks for the info. I'm thinking the weight might not be much of a factor in milling although I haven't tried it yet. The heavier bar might even help counterbalance the weight of the power head. I will probably try one or an Archer, which ever I can get cheaper. Either should be fine no more than I will use it.
Was the chain you refiled a full or semi chisel?

Sent from my Moto G (4) using Tapatalk

 

[Ck0461]

Chain that came with my bar was semi chisel. I’ve used full comp chisel and skip tooth. I like the skip tooth since there is less teeth to sharpen.

 

[Elitebowman]

I have used evey brand of chain on the market, including Laser. In my opinion there was no good or bad brand of chain, buy the Laser chain and bar and I am sure they will meet your cutting needs.

Hi, A friend of mine has a Stihl 038 Super chainsaw. There is a Laser Forestry Pro 24 " bar on it. I took it off looking for the stamp that would tell me how many drivers and what the pitch is. It doesn't have it on there. It has these numbers: 2025240721, under that it has O.E.M. something 10. I don't know if it is a 6,G,, C, or an O, or what before the 10. How can I tell the Pitch and how many drivers from those numbers in case he wants to buy a chain? Thank you for your time if you help me.

 

[Maintenance supervisor]

https://www.oregonproducts.com/en/bar-and-chain-measuring-tool/p/556418This is a good little tool to keep in your wallet, most 24" bars are 81 or 84 drive links in 3/8ths.

 

[Elitebowman]

https://www.oregonproducts.com/en/bar-and-chain-measuring-tool/p/556418This is a good little tool to keep in your wallet, most 24" bars are 81 or 84 drive links in 3/8ths.

Hi, thank you. I figured around 84 drive links, but I have to figure out the gauge size, .050 or .058. I can count the drivers but still need gauge. It doesn't have any numbers for Links, gauge or pitch on the bar. Just a series of numbers that I wrote on the Post. Thanks again for the Reply. Oh ya thanks for showing me that guide too.

 

[ammoaddict]

https://www.oregonproducts.com/en/bar-and-chain-measuring-tool/p/556418This is a good little tool to keep in your wallet, most 24" bars are 81 or 84 drive links in 3/8ths.

It is a cool little tool.

Sent from my moto g(7) power using Tapatalk

 

[Woodslasher]

Hi, A friend of mine has a Stihl 038 Super chainsaw. There is a Laser Forestry Pro 24 " bar on it. I took it off looking for the stamp that would tell me how many drivers and what the pitch is. It doesn't have it on there. It has these numbers: 2025240721, under that it has O.E.M. something 10. I don't know if it is a 6,G,, C, or an O, or what before the 10. How can I tell the Pitch and how many drivers from those numbers in case he wants to buy a chain? Thank you for your time if you help me.

If you can tell me the chain brand and the number on the drive links, I should be able to tell you what gauge it is.

 

[sean donato]

Laser is still made
https://www.lasersalesinc.ca/en/cha...-045-046-046m-048-056-056s-064-066-066-magnumI believe they are oem by sugihara, or at least the 20" light weight laser I have is.