Its real easy to make a spike 20min with a grinder i coppied mine from a picture but any old shape will do it.
McCulloch Chain Saws
- Thread starter Bruce Hopf
- Start date
Help Support Arborist Forum:
Heres a grinder jobby
Scott Sonntag
ArboristSite Lurker
Hey fella's
Hope y'all are all doing well. I posted a question on May 31st about material used to wrap a McCulloch chainsaw bar. I found a post from a quite a few years back that mentioned some interesting options. They recommended automotive heater hose, rubber tubing from online dealers, cold shrink tubing, etc. So I'll throw the question back out there again with this new info. Have any of y'all restored an older chainsaw with these materials? Or have y'all had any success with other types of material? To me, the easiest option is to go down to O'Reillys and pick up some heater hose but I'm all ears for what other options are available and if they have proved durable. Thanks for y'all time fellas
Scott
Hope y'all are all doing well. I posted a question on May 31st about material used to wrap a McCulloch chainsaw bar. I found a post from a quite a few years back that mentioned some interesting options. They recommended automotive heater hose, rubber tubing from online dealers, cold shrink tubing, etc. So I'll throw the question back out there again with this new info. Have any of y'all restored an older chainsaw with these materials? Or have y'all had any success with other types of material? To me, the easiest option is to go down to O'Reillys and pick up some heater hose but I'm all ears for what other options are available and if they have proved durable. Thanks for y'all time fellas
Scott
I've been looking for some non reinforced hose for some time but haven't had any luck. If you come across any, let us know.
Here's something to think about.Go to a place that sustom makes hydraulic hoses.A non-reinforced,non-braided hose should do the trick.I think the hydraulic hoses are heavier duty than the heater hoses.
Tim,I can get you fixed up when you get here next week.
Tim,I can get you fixed up when you get here next week.
Ok guys whats the od of the handles? Im at work so cant measure but... this is milk line is a nice soft rubber has a 15.7mm id and stretches to 25mm kinda size iv got it up against an inch galvanized pipe for comparison and its pushed over the threading machine handle and thats 25mm. It feels just like the factory handle. In nz u can get it anywhere and its very very durable.
One thing you want to be sure of is that the hose is fuel resistant. You don't want a handful of goo if it isn't.
Thats a good point there mite chuck some in gas for a night n see what happens. It deals with acid that eats your skin in a few seconds and boiling water
I've got one of those places right around the corner from where I live too.They sell milking machine parts,hoses,etc.I've been there to buy siphon hose for my wine making.The real test will be if it's petroleum product resistant.
I'll let you know what happens tomorrow and if its a good fit or not. That place will have off cuts for africa I know we do
My workmate assures me its fine in petrol he uses it to help it slip over stainless tube it drys up and grips like hell
Wetting the handle and inside of the rubber with water + dishwashing detergent also helps slip them on. It does make a mess while you are working on it so be prepared.
I have heard others mention some kind of cushioned tape like you would apply to bicycle handlebars works miracles too.
Mark
I have heard others mention some kind of cushioned tape like you would apply to bicycle handlebars works miracles too.
Mark
Yea bike tape works but doesn't look factory for the restoration guys. Im a mountain biker and my mates would give me as***les for having roady stuff on my saw haha. Gloves yea I wear them mainly for handling wood rather than the saw though. So wich saws came with rubber originally? I see alot with and without was it an option or only certain models? My pm10-10 has none I kinda assumed the 10-10 as the budget first full size mac and didn't come with those kind of luxuries but then I see some that have the rubber. Are they just retrofits from a higher spec model?
Well guys milk line tubing 15.7mm id 4mm wall thickness looks really close to the original and feels spot on I am absolutely stoked with it. A good work out getting it on though golly. Now I used waikato/skellerup tubing but all the brands are much of a muchness. Will only work with half raps of Course. But any way on to the next job rebuilding the broken section of the pm 800 clutch cover.
BigBlue
ArboristSite Operative
Jethro,
That does look like a great sub for the factory wrap. Good job finding it! I bet it was a bugger sliding it onto the handle though!
Rob
That does look like a great sub for the factory wrap. Good job finding it! I bet it was a bugger sliding it onto the handle though!
Rob
I haven't tried it but it make sense. Some guys have plugged the end of the tube and added an air fitting and blow compressed air into the tube once it has been started to make it easier to slide the tube on. It needs to be cut longer and then trimmed off once it's on the bar.
I'm going to give it a try once I find some appropriate tubing.
I'm going to give it a try once I find some appropriate tubing.
BigBlue
ArboristSite Operative
How do you remove the piston wrist pin on a PM800? Is there a hidden snap ring to remove? Or is it just pressed out using something like a deep socket of the right diameter? And how do you manage to get the needle bearings back together in the new piston when inserting the wrist pin?
Thanks,
Rob
Thanks,
Rob
Yea I used silicone spray in the end was still a battle and my hands are still sore now haha. Fossil ive seen people use an air gun underneath a dirtbike grip exactly the same way I think thats a great idea.
