MS660 Superstock

[056kid]

Sending pm

O word. .

I forgot to ax, what kind of torque should the nut be at? I can do inch or foot lbs. . .

 

[056kid]

So does anyone know what the stock timing is on a 660? I assume its before TDC.

Just trying to get a grasp on things. .

 

[mweba]

One of these?

 

[Tzed250]

One of these?

What in the world is that???.......:hmm3grin2orange:


.

 

[breymeyerfam]

What in the world is that???.......:hmm3grin2orange:


.

looks like some sort of round vise jaw holder aparter...

 

[gink595]

Pipe it:biggrinbounce2:

 

[2000ssm6]

Nice work! The 660 sounds great in the vid.

 

[056kid]

how come nobody does a pop up with a slight bevel instead of a step?

The bevel gives more comp and eliminates hot spots. .

Is it trendy or something?

 

[mweba]

This one was not finished yet. I smooth them out.

 

[Tzed250]

Pipe it:biggrinbounce2:

I would love it!!!

I will send an RFQ to you ASAP!!!


.

 

[Tzed250]

That's already so bad you scared the #### out of someone's dog!

That was our dog Bo...


.

 

[wigglesworth]

Looking good!!! Sounded a bit rich to my ears though....:dunno:

 

[Tzed250]

Looking good!!! Sounded a bit rich to my ears though....:dunno:

I would agree. It might pull another 250-400 rpm's with a tweak. Notice all of the oil in the cylinder in the pics, and that was after being shut off right after coming out of the wood. That being said, I'm not the kind to wring a saws neck with the H screw so I can gain .1 second in a cut. I would rather the saw be on the rich side of right. It did pull well from a 2-4 break into a clean two-stroke, but i still think that a 1/16 turn CW on the H screw will be ok.


.

 

[wigglesworth]

I would agree. It might pull another 250-400 rpm's with a tweak. Notice all of the oil in the cylinder in the pics, and that was after being shut off right after coming out of the wood. That being said, I'm not the kind to wring a saws neck with the H screw so I can gain .1 second in a cut. I would rather the saw be on the rich side of right. It did pull well from a 2-4 break into a clean two-stroke, but i still think that a 1/16 turn CW on the H screw will be ok.


.

Im with ya on that one. The saw I run the most still sounds fine and dandy at 15.5K, and pulls like a freight train, but I leave her all meek and timid at 14.5K. No sense in the extra wear and tear for that .1 second.

 

[pops21]

I'm xtremely impressed. I can't wait to see whats next.

 

[056kid]

I would agree. It might pull another 250-400 rpm's with a tweak. Notice all of the oil in the cylinder in the pics, and that was after being shut off right after coming out of the wood. That being said, I'm not the kind to wring a saws neck with the H screw so I can gain .1 second in a cut. I would rather the saw be on the rich side of right. It did pull well from a 2-4 break into a clean two-stroke, but i still think that a 1/16 turn CW on the H screw will be ok.


.

But that is stupid rich imo.

My 250R that runs @ 32:1 just has a little oily film on the movers, thats all she wants actually. . . .


Well Im done with commentary for tonite, too much sloe gin, well just the right amount . . . . .
Randy knows what Im talking about I think. . . . . . . . . . . . .

 

[AUSSIE1]

Great work Teez.

Good to see the work of art functional.

Your approach is wise as you learn more in steps.

 

[imagineero]

that saw just looks so clean!

have you run a few tanks through it before starting the mods? I dont have any experience with it myself, but some guys say you need to get a dozen tanks through a saw to wear it in.....

Shaun

 

[Tzed250]

.

There were maybe ten tanks through the saw before the mods. I broke the saw in fairly rich but now it is ready to eat...

.

 

[gink595]

I would love it!!!

I will send an RFQ to you ASAP!!!


.

I'll have some time this winter