My first new Stihl

[Evan]

I run full and skip on my 32 and 28 bars. I dont mind sharpening full comp. Its a stress reliever.

Full comp limbs better but skip will clog less in the cut when bucking passed the 32" tip
Full comp plunge cuts better. I find i plunge cut quite abit to keep from pinching the bar while bucking.
Both work in fir pine type stuff.

 

[JD Guy]

Oiler upgrade sounds good! Can you just add the parts to that oiler, or do you have to buy a complete one? Will the 1128 series pump or parts work?

IIRC just change the pump to a HO. I have not done mine yet but have the pn# and will get it on here later.

 

[bwalker]

IIRC just change the pump to a HO. I have not done mine yet but have the pn# and will get it on here later.

Thr control bolt and ramp is a bit cheaper and that's the only advantage to doing it that way.

 

[JD Guy]

I find that saw works better with a 20 in bar. It's a hot rod, not a tractor. Try the 20 with full comp.

I like my MS400. I changed to the large capacity clutch cover and dual spike. I am going to do the oiler upgrade as I too like a little more bar oil. It may be it’s just what I’m used to. It pulls non skip 25” just fine in white and red oak IMO. It will get a bit more lively alter using several tanks of fuel.

Oiler upgrade sounds good! Can you just add the parts to that oiler, or do you have to buy a complete one? Will the 1128 series pump or parts work?

 

[JD Guy]

The part # are courtesy of another member here on Arborist Site.

 

[StoneyMeadowMaple]

The part # are courtesy of another member here on Arborist Site.

And they fit in the 400 pump?

 

[Hman1024]

And they fit in the 400 pump?

Those parts should fit based on my research. SeeSawsRun has them on EBay btw.

 

[sean donato]

First, nothing is wrong with the oiler. Upgrade ad mentioned above. Second, it does indeed take 6-8 tanks to start making decent power. They pull a 24" bar just fine.

 

[bwalker]

And they fit in the 400 pump?

Yes

 

[StoneyMeadowMaple]

Got these in the mail today. Does anyone know the correct size screws? I assume allen head with some sort of lock nut. I assume I could find the right size screw easier than trying to buy Stihl screws?

 

[sean donato]

Just a heads up, I have a set of those, put them on, used them a few times then took them right back off and replaced them with the factory dogs. They hog up a lot of bar space for no good reason.
can't remember the screw size off the top of my head, but the local dealer had them in stock and they were like $3.00. (And this was the dealer that I don't typically use or reccomend just close to the house.).

 

[stihl sawing]

Just a heads up, I have a set of those, put them on, used them a few times then took them right back off and replaced them with the factory dogs. They hog up a lot of bar space for no good reason.
can't remember the screw size off the top of my head, but the local dealer had them in stock and they were like $3.00. (And this was the dealer that I don't typically use or reccomend just close to the house.).

Same here, i put them on a 460 and after a couple uses i took em off and gave them to a member here. not to mention they looked kinda dumb on a saw here in Arkansas. we have huge oaks but the bark is not really thick.

 

[StoneyMeadowMaple]

Just a heads up, I have a set of those, put them on, used them a few times then took them right back off and replaced them with the factory dogs. They hog up a lot of bar space for no good reason.
can't remember the screw size off the top of my head, but the local dealer had them in stock and they were like $3.00. (And this was the dealer that I don't typically use or reccomend just close to the house.).

I was worried about that, I was hoping they were somewhere in between, no complaints about them or the company, I was just hoping for something in between.