Also can someone please point in the direction for a manual for a 2000 woodsman
Nik's Poulan Thread
- Thread starter FATGUY
- Start date
Help Support Arborist Forum:
That is a very nice bar, but it would look better on the 8500 and a picture might be a nice thing to look at.
Hunt up beg for manuals on here SA and ask for what you need and it happens
This is one the little Poulan correct, the one you put a piston in?
Steve Sidwell
Steve Sidwell
All I have is a piece of manual, not much to go on. Got it years ago on beg for manual. Hopefully someone will have a complete one by now.
Steve Sidwell
Steve Sidwell
Here's a service manual
Yes it just a little guy but I put the new piston and jug and craps man 4218 plastic saw. I don't know if it was worth saving or not but it the kit was cheap so I figured at least it's a good learning experience Thank you
Thank you
This arrived in the mail today, not a super bar but it will do me a good job on a big poulan 24" 
Nice!
I like those bars because the sprocket nose is really easy to replace.
I have even converted a few Poulan .325 bars to .375.
I think I have 7 of them, if I find one that the cost is right I try and get it.
This last fall I had a problem with my 27 inch factory bar on my first 5400. The tip gave out and I was kind of down in the dumps about it and was trying to find a new tip but couldn't find one. Well I was looking at some old bars and there was one on a 16 inch bar with the same number on it. Took the rivets out and went to the hardware store and found some copper ones that would work and I had a new bar. I was so happy with my old junk pile and understand why I don't throw anything away.
This last fall I had a problem with my 27 inch factory bar on my first 5400. The tip gave out and I was kind of down in the dumps about it and was trying to find a new tip but couldn't find one. Well I was looking at some old bars and there was one on a 16 inch bar with the same number on it. Took the rivets out and went to the hardware store and found some copper ones that would work and I had a new bar. I was so happy with my old junk pile and understand why I don't throw anything away.
Just posting pic so I can see tip and bar that was on it. Thinking was a windsor if I recall right?
3 rivet ? Sending you link Todd for new ones to set back if so.
I believe Archer makes replacement noses for those as well. I was given a nice Husky pattern bar that must have been stored in a damp shed. The nose was permalocked and shot but the rest of the bar was more or less congealed in protective greasy grime. I think the nose was 9 bucks delivered.
Ax-man
Addicted to ArboristSite
Hey SVK, is that chain you posted on the other page that new Oregon PowerCut chain 72 EXL 3/8ths .050 full chisel chain . If it is it is good stuff. I have never been a big fan of Oregon but this chain has held up very good for the short time I have been using it . I am also running a 20 " Tsumura bar on a Poulan 3700 I redid awhile . I really like it . I was a little disappointed in the saw when I got it done but now that I have the carb dialed in and the new rings are seating it is getting better and better . I can definitely see why these saws have the following they do.
Has anyone ever did any light milling with one of these 3700/3400 ?? They seem like they would do a good job . I am on the look out for another Poulan to replace that 410 Homelite I have been using for light milling with a 20 " bar
Has anyone ever did any light milling with one of these 3700/3400 ?? They seem like they would do a good job . I am on the look out for another Poulan to replace that 410 Homelite I have been using for light milling with a 20 " bar
My poulan made skilsaw.http://cloud.tapatalk.com/s/5e1778ed4457a/20200109_125855.mp4
Sent from my SM-S767VL using Tapatalk
Sent from my SM-S767VL using Tapatalk
redunshee
Addicted to ArboristSite
NIce running saw
This 61 showed up the other day. In the project line it goes for now.
Hey, that looks nice! I was all set to shoot some video of my 68 today. Then my wife decided I didn't have enough to do so I played secretary instead. Checked out refinancing my truck. Gonna try an play with the 68 tomorrow.
