Oklahoma,AR,MO,KS,TX GTG (Next GTG 08/27/2016 ) Fort Scott, KS

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Mo. Jim, how far are you from St Joe? I need to make a run to the JD dealer tomorrow before noon.
If you need help unloading that load of hedge let me know, I will stop by and give you a hand.

Jim is 7 mi. South on 59 hwy.

Me, I'm on the corner of 29th & Duncan, just four blocks north of 36 hwy.. About four miles west of the John Deere dealer.
Horizon Equip. Has two locations here in Joetown.
Stop by and B.S..
 
You just want him to pull over that old remy. :D:D:D

I think I have found my least favorite firewood saw. Even if it is 131cc. That mono is a hog. But everyone knows it running:clap::clap::clap::clap::clap:

Get the chain figured out? I would have beat on it but didn't want to ruin it with my el cheapo Harbor Freight grinder. LOL
 
Morning all, had a small shower earlier, calling for scattered showers all day. I like my moisture in liquid form this time of year, no scooping or plowing.
Louis getting any meat in the freezer yet, or has your season opened yet?
Kenneth you need a 36 inch bar for that Mono.
 
got it

Charity Cut 8, December 13
Workshop+
Hedgerow
Awol
Hinerman
Oliver1655 with bucking trailer and splitter
Lurch2
Iowa
Shane & boys
blueberrymuzik

Spoke with Ed yesterday. Looks like we will have a tractor showing up for the Charity Cut. I hope the weather holds up. I'll pass on directions as soon as I get them. I'm planning on something yummy for lunch, too.
 
Ha! Told yah it was undersmall. Your turn in the barrel............................................

Jet screw fall out? Yikes!

H.S. jet is right rear bottom of carb. body. L.S. jet opposite side.

Yes it is didn't think to look on right side.:confused::confused:

Morning all, had a small shower earlier, calling for scattered showers all day. I like my moisture in liquid form this time of year, no scooping or plowing.
Louis getting any meat in the freezer yet, or has your season opened yet?
Kenneth you need a 36 inch bar for that Mono.


You going to volunteer to carry it.:D:D:D:D
 
Thomas, that reminded me that my wife's grandmother lived in Tahlequah so we've made that trim a few times! Every time I think of Oklahoma I think of Ray Wylie Hubbard's Choctaw Bingo... Lol...

Choctaw Bingo Ray Wylie Hubbard:


I am about 30 miles from Tahlequah---my old stomping grounds. I graduated from Northeastern State University there. Consumed a lot of beverages and stuff there; managed to graduate too, after 9 years of (see the beginning of this sentence). If you haven't been there in a long time you may not recognize a lot of the town. It has grown a ton over the last decade or so.

Cool vid with some bad jams. A lot of those pics brought back some memories.
 
I am about 30 miles from Tahlequah---my old stomping grounds. I graduated from Northeastern State University there. Consumed a lot of beverages and stuff there; managed to graduate too, after 9 years of (see the beginning of this sentence). If you haven't been there in a long time you may not recognize a lot of the town. It has grown a ton over the last decade or so.

Cool vid with some bad jams. A lot of those pics brought back some memories.
I fell in love with that old hardware store downtown Tahlequah! I could spend hours in there!
 
Yes it is didn't think to look on right side.:confused::confused:




You going to volunteer to carry it.:D:D:D:D

Sheesh! Buy 'em books and send 'em to school..............................................................................

Definitely needed more fine tuning but with the chain in the condition it was in it needed to be sharp to put a proper load on him.

That pup is a load the way it is! Maxed out this geezer's capacity.
 
Sheesh! Buy 'em books and send 'em to school..............................................................................

Definitely needed more fine tuning but with the chain in the condition it was in it needed to be sharp to put a proper load on him.

That pup is a load the way it is! Maxed out this geezer's capacity.

It is definitely only a GTG saw.
 
Made it to the stadium with my oldest daughter and nephew and we got to bride the train!
c37d552e00fdbe42e220d03d10f6c99b.jpg
0a926fb38c9b3e4968c932210163ac59.jpg
1650eba479348db80d84356797d918ee.jpg
 
Back
Top