Oklahoma,AR,MO,KS,TX GTG (Next GTG 08/27/2016 ) Fort Scott, KS

[lumberjackchef]

View attachment 287443View attachment 287444View attachment 287445View attachment 287446
Hey Everybody, Found this today before it went to the crusher. Found a tag at the front lower left next to the muffler says it's a Solo. But can't hardly read any numbers, even with a magnifying glass. First number looks like a 6000? Possibly a 626? or 70? Don't know, any ideas? The air filter cover is gone.

Its either a 635 or a 642. The 635 had a 54mm bore and the 642 had a 58mm bore. You would probably have to take the muffler off And measure to tell.

Sent from my SCH-M828C

 

[lumberjackchef]

I had a 635 for a couple of years big heavy vibration making monster, torquey beast of a saw. Had 404 30" hardnose bar. It pulled it just fine too!

Sent from my SCH-M828C

 

[andydodgegeek]

I've only got one chain ready. Tried it out this evening and I'm really liking how my 350 is breaking in. I need to work on this new chain I bought for the 385 it's not near aggresive enough.

I probably will just have my standard run of the mill woods chain, round ground, nothing special. Just dont think I will have much time to make anything fancy. Oh well what I will lack in quality I will make up for in quantity. Plannin on bringing a pile of saws to play with.:msp_w00t:

 

[lumberjackchef]

OK so I have to correct myself after looking over your pictures more closely I came to the conclusion that the pto side looks different than my 635 so I looked it up and it must be a 70 model.

Sent from my SCH-M828C

 

[workshop]

Hmmmm, Don't know. The cylinder looks different to me.

 

[Mo. Jim]

I need a chainbrake cover for a 36/40 Husky,the saw isn't nice enough to warrant the cost of a new one.

 

[workshop]

I'll have to bring it with me.

 

[moody]

I probably will just have my standard run of the mill woods chain, round ground, nothing special. Just dont think I will have much time to make anything fancy. Oh well what I will lack in quality I will make up for in quantity. Plannin on bringing a pile of saws to play with.:msp_w00t:

This chain isn't even worthy of the woods. The rakers are too high. I'm far from fancy and I can only fit so many saws in my Focus

 

[srcarr52]

Here's generally what the shirt will look like... I say generally cuz the words will be the same, but the shirt color may vary with the other supplier if we can get them done in time through him...

I'll buy a shirt.

 

[warjohn]

Guy in the bar next to me uses plain old dawn dish soap and water...

I've used that also but my blades lasted a lot longer with diesel, plus the mill I had ran on diesel so I always had it around.

 

[andydodgegeek]

I want a shirt! Make mine 3xl, gotta be able to fit in alota bacon wrapped little smokies!!!

 

[lumberjackchef]

I need a chainbrake cover for a 36/40 Husky,the saw isn't nice enough to warrant the cost of a new one.

I can probably hook you up. Im sure I've got a couple of those laying around. I'll look in the morning!

 

[Mo. Jim]

I can probably hook you up. Im sure I've got a couple of those laying around. I'll look in the morning!

Thanks,let know,do you still need that 3400 crankcase?

 

[lumberjackchef]

Hmmmm, Don't know. The cylinder looks different to me.

Here's what makes me think that........Model 70

I'm pretty sure thats the only model with the oil cap up there that I can remember seeing. Could be wrong though.......

 

[lumberjackchef]

Thanks,let know,do you still need that 3400 crankcase?

Yes sir, bring it along. I can always use one of those!

 

[Mo. Jim]

I want a shirt! Make mine 3xl, gotta be able to fit in alota bacon wrapped little smokies!!!

That 3xl would make me two and mabey three shirts. I have been bulking up,so I can run that 999 Ole of srcarrs and my Remy. 754G,up to 136 pounds.:msp_thumbsup:

 

[andydodgegeek]

I want a nice looking clutch cover for my 346xp, an orange one. Anyone have one. I think a 350 cover would work, correct me if I am wrong. Not alot to trade, but I can steal money from Sarahs purse.:smile2:

 

[cowroy]

I want a nice looking clutch cover for my 346xp, an orange one. Anyone have one. I think a 350 cover would work, correct me if I am wrong. Not alot to trade, but I can steal money from Sarahs purse.:smile2:

Andy, I have a 350 that was straight gassed on the first tank with an orange cover. It's yours if you want it. Were you wantin to trade yours or just buy one and keep yours? You can pm me.

 

[cobey]

thanks Chad!!! :smile2: (lumberjackchef) for helping with my saws and hanging out today!
great to learn new stuff! I know what real hotrod saws sound like now :smile2:

 

[Work Saw Collector]

but I can steal money from Sarahs purse.:smile2:

let me know how that works out for you, I'm a little short myself.