Olympyk, Olympic, Oleo Mac, Emak, Efco, Blitz, Folux, Spartan, Spartacus thread
- Thread starter jerrycmorrow
- Start date
Help Support Arborist Forum:
Unless it's been run over by an 18 wheeler or a bulldozer it still has a possibility.The poor saw just needs a few parts & some TLC.Lol
Walter Glover
ArboristSite Guru
An Oleo Mac Olympyk 935f came into my possession. Cute little saw. Needs air filter and it looks to me like the oiler plunger is missing. The oiler body with spring is here but nothing to pump the oil. Sound right fellas?
Good compression and good plastic. Popped strong with squirts of fuel. All positive indicators so far
Good compression and good plastic. Popped strong with squirts of fuel. All positive indicators so far
Hi Gang,I've got an Olympik 254 that I've been working on since July when I bought it.I bought another saw for parts & finally got the oiler out to put in my original saw.Now I've misplaced the fitting that holds the oiler in place.I believe it's made of aluminum & screws into the front of the saw.If anyone would have an extra one I'd gladly pay for it.Thanks!
Ed
Ed
Update - I found an oil pump ring nut brand new,so I won't be needing any from anyone here.I do have some parts that I'd be willing to sell cheap.I have a top cover for a 254/264 w/switch,two BN oil caps,one extra felling spike,one 254 handle bar,one rear handle assembly, one BN air filter cover for 264 (I believe),& one 264F chain brake.
Ed
Ed
Hi All,I just picked up asn Olympik 234 off Feebay for $14.It has very good compression & spark.I put some fuel mix down the carb & she fired right up.I located an air filter & cover for it,but after unpacking the saw I went to put the bar & chain on it & found that it's missing the bar plates.If anyone would have a set of them I'd greatly appreciate it if I could get them.I'll pay for them of course.
Ed
Ed
raumati01
ArboristSite Operative
Does anyone know which carb kit I need for a 971?
You need to find out what carb you have in the saw first.Also,which saw brand do you have,Efco,Olympik,etc.?
Brad Nelson
New Member
Was given a 950f super to try and rehab. Not very small engine repair saavy. Starter cord pulls really hard. Pulls fine with spark plug removed. Took muffler off. Black oil spitting out of cylinder into muffler. Some scoring inside. I hear a hissing noise when I pull the starter with the plug in, like it's struggling to pull in air.
I was given this saw by my boss to see if we can do anything with it. Doesnt look like it was ever cleaned. Any advice on what the problem could be or if it's worth the trouble if there a crack somewhere. Thanks
I was given this saw by my boss to see if we can do anything with it. Doesnt look like it was ever cleaned. Any advice on what the problem could be or if it's worth the trouble if there a crack somewhere. Thanks
I bought a little 234 about 2 mo.ago.It was missing the air filter & cover & I managed to get them.I rebuilt the carb,it runs rough,but I found that the oiler isn't working.It's an automatic oiler & has no manual backup oiler.How do I find out what the problem is with the oiler?
Ed
Ed
Just for fun (?), I did a comp check on the three 264F I have.
185, 190 & 190. WOW!
185, 190 & 190. WOW!
Ciupav Gheorghe
New Member
Hello & welcome to Arboristsite! You are posting in the correct area.Not much is known about the Blitz saw other than it was one of the many names that Oleo Mac used at the time.I believe this brand was sold primarily in Europe.What country are you from?You might be able to get more information by going to the"beg For Manuals"section where you found the Chainsaw Stickies for this saw.Just make a post there requesting a manual or IPL for this saw.If you have no success there,the parent company is now called Efco.You might get some info from them.
Ed
Ed
Hi @Ciupav Gheorghe
The B-52 Super should be an Oleo Mac 350 super
http://acresinternet.com/cscc.nsf/e...62716032d3c7927788256bc500566356?OpenDocument
Attached is an ipl which also shows the crossover to Oleo Mac and Folux saws.
Sorry never found a service manual.
Ray
Little Al
Addicted to ArboristSite
Blitz was more common in Australia /New Zeeland VAP was a more common badged European offering
To me it looks pretty much like an Olympyk 264 equivelent.
S
Make sure the oil line is solid and stable and is attached and the filter is clean inside the oil tank.
If thats not it check for o-rings on the rod
Not it? Youll have to change the cam out on the flywheel end of crank. Press fit. Cam could be spinning or could be worn down. No fun either way. Gotta find new cam, pull the existing cam, install “new” cam. May be as well off pulling from a parts saw
Start with the easy.
Make sure the oil line is solid and stable and is attached and the filter is clean inside the oil tank.
If thats not it check for o-rings on the rod
Not it? Youll have to change the cam out on the flywheel end of crank. Press fit. Cam could be spinning or could be worn down. No fun either way. Gotta find new cam, pull the existing cam, install “new” cam. May be as well off pulling from a parts saw
That explains the problem I had with my 254 about 15 or so yrs.ago.The owner of the saw shop kept putting oilers in the saw.It'd oil when it was cold,but as soon as it got hot it'd stop oiling.I ended up scrapping the saw,but I've got a sneaking suspicion that I bought my old saw back for $20 & the oiler was missing.I never got around to putting an oiler in that saw yet.I pieced it together with a recoil from yet another 254 & rebuilt the carb.
As for the 234,I haven't messed with it either for a couple of months,too many projects.Lol Ed
As for the 234,I haven't messed with it either for a couple of months,too many projects.Lol Ed
Hey guys, this seems to be the thread of people in the know about oleo mac saws, so I'll post a link to a thread I started. If anyone could help me identify these model #s it would be appreciated. Seems like info on these is in short supply.
https://www.arboristsite.com/community/threads/oleo-mac-parts-galore-help.327860/#post-6763830
https://www.arboristsite.com/community/threads/oleo-mac-parts-galore-help.327860/#post-6763830
got a oly? chop saw couple wk ago. curious if anyone here can id. looks 272 & 284ish, what I can gather here.
gonna try get pics on.
Did you ever find a part #? Your picture is the first one I've seen matching some parts I've been trying to identify. I assumed they were chainsaws, but now it makes sense that it's a chop saw. That's why I could never match a picture of the clutch cover.
Attachments
Similar threads
- Locked
