Pioneer chainsaws

[Cookie]

ra was latest/greatest when I was new. one o the reasons for my 1st old saw. in av pic.

their ol building is still here, too. right next door to mike acres' warehouse.

View attachment 629193 View attachment 629194

Where is this Pete ?

 

[pioneerguy600]

Where is this Pete ?

Last time I was out there he was at 3921 Phillips Avenue in Burnaby.

 

[Cookie]

Last time I was out there he was at 3921 Phillips Avenue in Burnaby.

Might be a 3.5 hour bike ride in my future this summer

 

[2stroke_shaman]

I got off early so I took some lightweights out for a playday . Have to take use of 46F temps . The p 28 cut well with a file fixed chain . It needs a treatment. Clutch worn . Oil pump might be bad . Any words of advice?

 

[Cookie]

I got off early so I took some lightweights out for a playday . Have to take use of 46F temps . The p 28 cut well with a file fixed chain . It needs a treatment. Clutch worn . Oil pump might be bad . Any words of advice?

View attachment 629603

Send it to me and be done with it.

 

[Walter Glover]

That building is at 7342 Winston Street, Burnaby
Found it on google maps just 'drivin' around lol

 

[rocketnorton]

Burnaby. Winston/Philips.

 

[Cookie]

What you guys doing with these black reed blocks with cracks around the threaded insert ? My 3071 and Farmsaw both have cracks Are they leaking air? An they be repaired?

 

[Cookie]

I got off early so I took some lightweights out for a playday . Have to take use of 46F temps . The p 28 cut well with a file fixed chain . It needs a treatment. Clutch worn . Oil pump might be bad . Any words of advice?

View attachment 629603

I have a p28 parts saw. I can see if it has a clutch on it if you need.

 

[leecopland]

I believe I have a spare clutch for that series Pioneer.

 

[Cookie]

Seller said it ran good, a week later it was on my door step. My new to me p41! Figured we had a problem when it only pulled 60 psi. Surprised it fired right up tho. Haha. Not sure the cylinder is good, Piston is toast. Who’s sellin? This is my first top end job on a saw.

 

[PogoInTheWoods]

At least it has spark!

 

[Cookie]

At least it has spark!

And a fuel cap!

 

[p61 western]

Seller said it ran good, a week later it was on my door step. My new to me p41! Figured we had a problem when it only pulled 60 psi. Surprised it fired right up tho. Haha. Not sure the cylinder is good, Piston is toast. Who’s sellin? This is my first top end job on a saw.

That's a bummer the top ends are hard to come by for that saw.

 

[Cookie]

Can you big bore a p41?

 

[Cookie]

Any quality in this stuff?

 

[2stroke_shaman]

I believe I have a spare clutch for that series Pioneer.

PM sent.

 

[huck01955]

Here are some Pics of my Farmsaw 11, changes made from original are l swap out the half wrap to a Full wrap handle bar and replaced the 4 shoe clutch with the 3 shoe clutch off the orange Farmsaw.
the original reed block was cracked and saw would not run properly so l replaced it with a new reed block assy and Saw now passes a Pressure /Vac test

Outstanding work

 

[p61 western]

View attachment 629842

Any quality in this stuff?

I used one and after some fitting it seems to be ok. It's in a saw I did for my bil, and have had no complaints.

 

[p61 western]

Can you big bore a p41?

Not to likely and the cost to replate can be spendy.